HVAC 310 Flashcards

1
Q

Which type of fans have a low noise emission and are suitable for restaurant exhaust or where air contains moisture or dust ?

A

Backward Inclined Blades Fan

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Duct construction 110304B

Name the 7 different pressure and their 3 classifications

in Inches of Water Column and seal classifications

A

Low pressure, 1/2 - 1 - 2 (C)
Medium Pressure 3-4-6 (B)
High pressure 10 (A)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Duct construction 110304B

What need to be done before designing the ductwork

A

Load calculation and the overall type of distribution system.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Duct construction 110304B

What placement should the screws have on round pipe

A

Minimum of three screws should be placed on duct of diameter of 14inches or less and uniform intervals of at least 15inches along the circumference for higher diameter duct.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Duct construction 110304B

what is the Gyrth joint?

A

Beaded sleaved joint (aka connecting collar)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Duct construction 110304B

what type of joint is the most popular on round pipe.

A

Slip or Lap joint is the most popular.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Duct construction 110304B

What is another name for companion flange used on pipe with a diameter of over 60 inches.

A

Vanstone flange.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Duct construction 110304B

Butt weld is the strongest joint and can be used on all pressure classes.

A

true

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Mechanical air movement and control 110401C

Type of fan that have low noise emission and is suitable for restaurant exhaust system or where air contains moisture or dust.

A

Backward inclined blades.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Mechanical air movement and control 110401C

How is the location of the motor determined?

A

By facing the drive side of the fan. W,X,Y,Z.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Mechanical air movement and control 110401C

What should be the length of the splitter damper?

A

1.5 times the small duct width.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Specifications and schedules and schedules 110304C

How would the size be shown for duct acoustically lined on a print?

A

Inside dimension, need to be upsized for ordering.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Specifications and schedules and schedules 110304C

You are asked to order a duct 16 by 20 with 2 inches of acoustic insulation. what size will you order.

A

20 by 24.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Specifications and schedules and schedules 110304C

How would acoustic insulation be shown ?

A

doted lines.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

Specifications and schedules and schedules 110304C

When velocity exceed 4000fpm what should be done to the acoustic insulation?

A

metal nosing on edge of the duct.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Light commercial installation Procedures 110204e

What can oppose blades damper be used for?

A

For balancing.

17
Q

Light commercial installation Procedures 110204e

HVAC leakage test

14inches round, 200feet long

A

7cfm per 100sqft.
total 51.4 cfm of loss.

18
Q

Light commercial installation Procedures 110204e

Do we need to worry about velocity in leakage test

A

No

19
Q

Duct construction 110304B

Is standing seam the easiest to weld ?

A

Yes

20
Q
A