General Knowledge Vessels Flashcards

1
Q
  1. Name 3 locations diving operations can be carried out from?
A

Fixed platforms and temporary fixed platforms.
Small craft - daughter craft vessels
Specialist locations - barges
Large barges and multihulls DSV’s

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q
  1. What classification of vessels are required for DP diving ops?
A

Class 2 and 3

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q
  1. What’s the purpose of a DP system?
A

To maintain position keeping of the vessel.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q
  1. What’s the 5 systems required in a DP system?
A
Power system
Propulsion system
Sensor system
Control system 
Reference system
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q
  1. What’s the maximum power percentage output allowed for brief periods of the thrusters?
A

80%

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q
  1. What’s the 3 colors displayed in a dive control in a DP alert status box and what does it means?
A

Constant GREEN LIGHT - normal operation status
Flashing YELLOW LIGHT - degraded operation status
Constant RED LIGHT with audible alarm - DP emergency status

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q
  1. What’s the minimum personal required in a DP control room during dive operations?
A

2 - one been fully competent for all aspects of DP control without supervision.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q
  1. What’s the minimum DP duration before commencing dive operation?
A

30 minutes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q
  1. What lights are displayed at night to indicate a vessel on DP carrying out diving operations?
A

RED - WHITE - RED

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q
  1. What Symbols are displayed in the day light to indicate a vessel on DP carrying out dive operation?
A

BALL - DIAMOND - BALL

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q
  1. What’s the minimum separation between diving basket or bell and the subsea asset?
A

5 meters

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q
  1. Vessels movements should be orientated around what, during diving ops?
A

The work station, always notify dive supervisors, divers and ROV.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q
  1. The shallow the water the greater the scope of Taut wire movement.
    True or false?
A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q
  1. What’s the minimum distance should be maintain between anchor chains and the bell or diving baskets?
A

50 meters or indicated in the company manual.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q
  1. What’s the recommended distance for moving the vessel when changing locations with diver in the water?
A

5 meters increments

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q
  1. A DP system can be disturbed subsea when carrying out dive ops, by what?
A

Bell flushing
Divers free flow
Large volume of compressed air - dumping
HP water jet

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q
  1. Name 2 propulsion systems?
A

Azimuth thrusters
Tunnel thrusters
Main engines propellers and rudder.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q
  1. Name 3 types of position reference systems. PRS?
A
Tault wire
Hydro-acoustic Position Reference. HPR
Differential Global Positioning System. DGPS
Laser Radar System. 
FM radar system.
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q
  1. What’s the recommended distance to maintain separation between a ships beacon to and subsea asset?
A

10 meters

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q
  1. What’s the maximum angle of deflection when using a tault wire before having to reset reference ?
A

15 degrees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q
  1. How many DP reference systems are required for diving operation to commence?
A

3 systems.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q
  1. What are the 6 main vessels movements and specify them?
A

HEAVE - up and down of the vessel
SWAY - moving straight to port and starboard of the vessel
SURGE - forward and stern of the vessel
ROLL - rolling to port and starboard
PITCH - rolling bow and stern
YAW - circular movement keeping the centre of the vessel

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q
  1. DMAC 012 recommends the dive ops should not be carried out with certain distances of seismic surveying. What’s the minimum recommended without contact with survey vessel?

A) 5km
B) 10km
C) 1200m
D) Where diving and seismic activity will occur within a distance of 30km (18.6 miles) a joint risk assessment should be conducted, between the clients/operators involved and the seismic and diving contractors in advance of any simultaneous operations

A

D) Where diving and seismic activity will occur within a distance of 30km (18.6 miles) a joint risk assessment should be conducted, between the clients/operators involved and the seismic and diving contractors in advance of any simultaneous operations

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q
  1. What zone is safe to use Artemis units?
A

Zone 1

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Q
25. What sign is circular on blue background with symbols in white?
A) prohibition sign
B) warning sign
C) safe condition sign
D) mandatory sign
A

D) mandatory sign

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
26
Q
28. What sign is circular with red border and a crossbar over a black symbol on a white background ?
A) warning sign
B) prohibition sign
C) mandatory sign
D) safe condition sign
A

B) prohibition sign

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
27
Q
  1. On a DP vessel, communications when diving must be provided between?
    A) dive control and masters cabin
    B) dive control and engine room
    C) dive control and LST cabin
    D) dive control and ships crane if being used for diving ops
A

D) dive control and ships crane if being used for diving ops

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
28
Q
  1. In conditions of reduced visibility, decisions about the suitability for diving from DP vessels should be rest with?
    a) the LST supervisor
    b) the diving superintendent
    c) the diving supervisor & captain / OIM
    d) the radio operator
A

c) the diving supervisor & captain / OIM

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
29
Q
  1. What’s the single most important criterion for the diver exposed to LOW frequency sonar?
    a) vibratory sensation in the hands, arms and legs
    b) DCI
    c) Unable to hear supervisor over the comms
    d) disorientation due to vestibular stimulation.
A

d) disorientation due to vestibular stimulation.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
30
Q
  1. Your DPO informs you there is a fishing boat approaching the DSV and he is unable to contact them by radio. What action would you take?
    a) continue normal diving ops
    b) abort the dive and recover the bell
    c) warn the divers to standby to move to agreed safe place
    d) tell the DPO to move the vessel
A

c) warn the divers to standby to move to agreed safe place

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
31
Q
  1. When diving on DP in shallow water, which of the following is least affected?
    a) vertical tault wire
    b) radio or surface position reference
    c) acoustic system HPR
    d) vessel capability
A

b) radio or surface position reference

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
32
Q
  1. An acoustic beacon for the DP PRS should not be located within what distance of the subsea structure?
    a) 5m
    b) 10m
    c) 30m
    d) 100m
A

b) 10m

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
33
Q
54. What sign is a triangle with a black border and a symbol on a yellow background?
A) prohibition sign
B) warning sign
C) safe condition sign
D) mandatory sign
A

b) warning sign

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
34
Q
  1. Under U.K. regs, what’s the minimum number of the independent position references system “ in use” during DP diving ops?
    a) 1
    b) 2
    c) 3
    d) 4
A

c) 3

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
35
Q
  1. In addition to the diving supervisor, whom should he DP operator inform of an “Alert status”?
    a) LST
    b) master and diving supt
    c) master and client rep
    d) diving supt and client rep
A

b) master and diving supt

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
36
Q
  1. If diving alongside a platform at 100msw, where over the side tubular work is in progress, how far should the dive station be away from the platform?
    a) 100m
    b) 30m
    c) 130m
    d) 1000m
A

c) 130m

1. 3m times depth

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
37
Q
  1. All divers in the water should have a communication system that?
    a) allows direct comms with supv
    b) uses unscrambler for helium mixtures
    c) is recorded & kept for 48h
    d) all of the above
A

d) all of the above

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
38
Q
  1. Who has the responsibility to direct a diving ops safely?
    a) the superintendent
    b) the client
    c) the supervisor
    d) the master or OIM
A

c) the supervisor

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
39
Q
  1. Who has the responsibility to ensure that the diving regs are complied with?
    a) the client
    b) the operator
    c) the principle contractor
    d) the master or OIM
    e) the supervisor or project manager
    f) all of the above
A

f) all of the above

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
40
Q
  1. SI 2776/1997 covers?
    a) commercial diving offshore only
    b) commercial diving inland/inshore only
    c) both of the above
    d) diving into that pub in Peter head
A

c) both of the above

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
41
Q
  1. Who has a duty to disclose information, and to ensure there actions do not endanger the divers safety?
    a) clients or their representatives
    b) master or OIMs
    c) crane drivers, maintenance personnel
    d) everyone involved in the diving project directly or indirectly.
A

d) everyone involved in the diving project directly or indirectly.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
42
Q
  1. The client, OIM, master and any other person having responsibility for a diving location, must have in writing ?
    a) the name of the diving contractor
    b) tests and certificates for diving equipment
    c) the names of the divers
    d) the times and locations of the tea breaks
A

a) the name of the diving contractor

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
43
Q
  1. A risk assessment shall be Carried out…
    a) only on risk to members of the dive team
    b) within 24h of them being identified
    c) before the diving project starts
    d) only on risks to the public arising from the diving project
A

c) before the diving project starts

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
44
Q
  1. Risk assessment are required under?
    a) the diving regulations SI 1997 2776
    b) the management of health and safety at work regs 2004
    c) the national association of the housewife’s and mother’s
    d) both a and b
A

d) both a and b

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
45
Q
  1. The diving project plan would include…
    a) the outcome of the risk assessment
    b) contractor operating rules
    c) diving techniques and procedures
    d) contingency plan to manage recognize risks
    e) all of the above plus more
A

e) all of the above plus more

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
46
Q
  1. Comms between a seismic vessel surveying and DSV should be continuous where the operating distance is LESS than?
    a) 5km
    b) 10km
    c) 1km
    d) 15km
A

a) 5km

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
47
Q
  1. State and explain the reference systems for DP vessels.
A
  • tault wire: lateral movement detected by sensor head on boom. Depressor weight on seabed. The deeper the water the greater the operating radius of the vessel.
  • Artemis: the mobile antenna is on the vessel & the fixed antenna is on the jacket, shore, fixed location
  • acoustic: transducer under the ship and a transponder on seabed.
  • satellites DGPS
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
48
Q
  1. State the limitations of these reference systems?

Tault wire, Artemis and HPRS.

A
  • Tault wire: if the wire is not kept in straight line, shallow water or fouled in/on structure. Max usual deflection 15°. All equipment should be clear of wires, min of 5m above & 10m to side of any subsea structure.
  • Artemis: blockage of the signal
  • acoustic: deeper the water, longer takes to react. Maybe out of range. Water jet aeration affects.
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
49
Q
  1. What you need to know about vessel movements with the diver in water?
A

a) max movement any direction - 10m ( often done 5m steps)
b) max 5° heading change
c) cannot change both distances & heading at the same time.
d) thrusters must not exceed 80% of power capability for more than “brief and isolated periods”
e) most common cause of DP incidents is operator error
f) visibility under 0.5nm is NOT recommended for surface orientated diving.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
50
Q
  1. What’s the most common cause leading to fire?
A

Bad housekeeping.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
51
Q
  1. During diving ops, how many reference systems must be online?
A
  • at least 3 different position system should be online
  • 2 of them should be different type

note: should have 2 anemometers, 2 vertical reference sensors and 3 gyro compass
* Anemometers not considered reference system.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
52
Q

Which DP system is most likely to be affected by the pitch and roll of a DP vessel?

a. DGPS
b. Taut wire
c. Acoustic transponder
d. Artemis

A

b

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
53
Q

During DP diving operations a diver umbilical must be physically restrained at the
tending point to prevent him from coming within:
a. 3 metres of the thrusters
b. 5 metres of the thrusters
c. 7 metres of the thrusters
d. 10 metres of the thrusters

A

b

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
54
Q

During DP vessel movements, on-line position references shall be:

a. one in number
b. two in number
c. three in number
d. four in number

A

c

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
55
Q

A DP Vessel can be defined as in NORMAL OPERATIONAL STATUS when
which of the following apply?
a The vessel is under DP control and the DP system is operating
normally with all the appropriate back up systems available
b Vessels indicated position and heading is within pre-determined limits
for all but brief and isolated periods
c When no risk of collision exists
d All of the above

A

d

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
56
Q
A flashing red light in dive control on a DP Vessel is accompanied by:
a A PA announcement from the bridge
b A distinctive audio alarm 
c An alternative green and yellow light
d A warning sign on the display
A

b

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
57
Q

When a DP Vessel is operating a vertical taut wire reference system:
a The operating radius is increased in shallower water
b The deeper the water the greater the operating radius
c The operating radius remains the same regardless of depth

A

b

58
Q

Horizontal operation clearance between a suspended mooring line and a deployed bell should normally be a minimum of:

a. 20 metres
b. 50 metres
c. 60 metres
d. 100 metres

A

b

59
Q

The Mobile antenna of the artemis system is:
a The antenna on the platform or structure
b The antenna on the vessel
c Neither of the above
d A combination of one or both of the above

A

b

60
Q

During diving operation from a DP Vessel the minimum normal acceptable reference systems deployed, connected to the DP computer(s) and in use is:
a One with one on standby
b At least two, with one on standby
c Three
d One, one on standby and one switched off

A

c

61
Q
The DP operator must apply which status if the available power units are reduced to the level that failure of one more could prevent the vessel holding position:
a Yellow 
b Green
c Red
d None
A

a

62
Q
Of the following, which is incorrect:
a Artemis, 2 acoustic transponders, taut wire
b 2 taut wires, 1 acoustic transponder
c 2 taut wires, 3 acoustic transponders
d 3 acoustic transponders, artemis
A

d

63
Q

In an air dive through the moonpool of a DP diving support vessel, diving
should only take place if the dive depth exceeds the operating draught of the
vessel:
a Plus 5 metres
b Plus 10 metres
c Plus 15 metres
d Plus 20 metres

A

b

64
Q

The DP operator will apply the red alert under which of the following conditions:
a Failure or loss of one DP computer
b Reduction of independent position sensors to one
c System failure results in an inability to maintain positioning or heading control
d The vessels indicated position strays beyond the set limits for more than brief and isolated periods.

A

c

65
Q
What alert level must be activated by the DP operator if there is a possible risk
of collision:
a Yellow 
b Red
c Green
d None
A

a

66
Q

On DP the divers maximum length of umbilicals will not be greater than:
a The distance between, surface and the wet bell or basket.
b The distance between the nearest thruster and the point of tending less 5 metres
c The draft of the vessel
d The distance from basket and work site

A

b

67
Q
Horizontal clearance between a suspended mooring line, and a deployed basket or bell should normally be a minimum of
a 20 metres
b 50 metres 
c 60 metres
d 100 metres
A

b

68
Q

Why should care be taken in the use of water jets from a DP vessel?
a Diver is exposed to excessive noise
b Operating noise may interfere with the acoustic transponder
c Disruption of communications
d Interference of navigation system by pump

A

b

69
Q

What constitutes a Zone I area?
a An explosive gas and air mix could occur in a normal operation
b Breathing sets being worn
c An explosive gas and air mix is always present
d An explosive gas and air mix is unlikely to occur and when it does, it
will pass rapidly

A

a

70
Q
Using the Beaufort wind scale a gale is:
a 23-28 knots
b 28-34 knots
c 34-40 knots 
d 40-45 knots
A

c

71
Q
An imminent gale warning is:
a 0-6 hours 
b 6-12 hours
c 12-24 hours
d 24-36 hours
A

a

72
Q
While on DP the maximum heading change allowed is:
a 5 degrees
b 10 degrees
c 15 degrees 
d 20 degrees
A

c

73
Q

A diver, working from a DP Vessel, is about to operate a HP Water Jetting
gun. Which of the following precautions applies?
a The tender takes up divers slack
b The Dive Supervisor informs the DP Operator on the bridge
c The yellow light in Dive Control is switched on
d The diver’s platform is recovered to surface

A

b

74
Q

A transducer when used as a reference system for a DP Diving Operation can
be used:
a With a number of different transponders
b In conjunction with a number of different transducers
c Only if used with a transponder on the end of a taut wire
d Only if used with a transponder on the artemis fixed position

A

a

75
Q

The frequency of a Divers Hand Held Locator is:

a. 37.5 KHz
b. 40.0 KHz
c. 55.5 KHz
d. 73.5 KHz

A

a

76
Q

On the Beaufort scale a strong breeze is:

a. Force 1
b. Force 2
c. Force 5
d. Force 6

A

d

77
Q

Under the IMO after July 1994, how many classes of DP vessels are there?

a) 1
b) 2
c) 3
d) 4

A

c

78
Q

What alarm would indicated a DP “degraded operational status”

a) steady green light
b) steady red light
c) flashing yellow light
d) flashing blue light

A

c

79
Q

In addition to the diving supv, whom should the DP operator inform of an “ alert status”

a) LST
b) master and diving supt
c) master and rep client
d) diving supt & clientrep

A

b

80
Q

When diving with anchor patterns, what’s is the minimum distance between the diving stage and any mooring lines?

a) 15m
b) 50m
c) 100m
d) 3m

A

b

81
Q

What’s considered a min safe distance of tault wire from UW structure ?

a) 3m
b) 5m
c) 10m
d) 15m

A

c

82
Q

How far would a platform protrude at 50msw with a batter of 1 in 10?

a) 5m
b) 50m
c) 51m
d) 500m

A

a

83
Q

What’s the average limiting vertical angle of a tault wire when re-location became necessary ?

a) 5 degrees
b) 15 degrees
c) 30 degrees
d) 10 degrees

A

b

84
Q

The vertical tault wire can be deployed and recovered in diving mode with permission of?

a) the master
b) OIM
c) diving supervisor
d) superintendent

A

c

85
Q

When a weather forecast gives the wind direction as veering, which direction is it traveling?

a) north to south
b) clockwise ( sw to w)
c) anti-clockwise
d) east to west

A

b

86
Q

How high should a diving stage or wet bell be kept above a wellhead structure?

a) 5m
b) 10m
c) 15m
d) 20m

A

a

87
Q

What’s the minimum surface visibility considered for safe DP diving ops?

a) 150m
b) 100m
c) decide by master and diving supv
d) decided by dive supt

A

c

88
Q

When fog or mist is possible during diving ops, whom should you consult as to safety?

a) project manager
b) master of the vessel
c) radio op.
d) divers

A

b

89
Q

A DP vessel can be defined as in NORMAL OPERATIONAL STATUS when which of the following apply?

a) the vessel is under DP control and the DP system is operating normally with all the appropriate backup system
b) when thrusters output and total power consumption does not exceed 80% of the maximum thrust or total available power for more than a brief and isolated periods
c) vessels indicated position and heading is within pre-determined limits for all but brief isolated periods
d) when no risk of collision exists
e) all of the above

A

e

90
Q

When a DP vessel is operating a vertical tault wire reference system….

a) the operating radius of the vessel is increased in shallower water
b) the deeper the water, the greater the operating radius of the vessel
c) the operating radius of the vessel remains the same regardless of depth
d) all of the above

A

b

91
Q

The mobile antenna of the Artemis system is…

a) the antenna on the platform or structure
b) the antenna on the vessel
c) neither of the above
d) a combination of one or both of the above

A

b

92
Q

When the vessel moves about its centre vertical axis to compensate for wind or sea does it?

a) list
b) surge
c) yaw
d) sway

A

c

93
Q

Which of the following is not a position reference sensor?

a) tault wire
b) artemis
c) hydro acoustic reference
d) anemometer

A

d

94
Q

Which DP reference sensor system must always be operating during DP diving ops?

a) tault wire
b) Artemis or surface reference
c) INS
d) HPR

A

b

95
Q

What’s the minimum number of independent position reference system in use during DP diving ops?

a) 1
b) 2
c) 3
d) 4

A

c

96
Q

How long should the vessel be held on DP before diving ops commence?

a) 30min
b) 1h
c) 90min
d) 2h

A

a

97
Q

There must be how many qualified persons in the control room at all times when continuous diving?

a) 1
b) 2
c) 3
d) 4

A

b

98
Q

Define significant wave height.

A

Average Height of the largest one third of all waves recorded over a 10 minute
period

99
Q

Define the Coriolis effect.

A

A wind driven sea current – not the same direction as the wind but an angle of 45⁰ to it.

100
Q

The near by platform has stopped all over the side work because the visibility is so poor the standby vessel could not see any possible man overboard, should?
a Diving stop for the same reason
b Ignore it as it isn’t foggy underwater
c It’s up to the vessel master only to decide
d Haven’t the foggiest idea

A

a

101
Q

An imminent gale warning is…

a) 0-6 hours
b) 6-12 hours
c) 12-24 hours
d) 24-36 hours

A

a

102
Q
Name a rotational degree of freedom controlled by D.P.?
a Surge
b Sway
c Yaw 
d Heave
A

c

103
Q
Using the Beaufort scale, a gale is?
a 40-45 knots
b 34-40 knots 
c 23-28 knots
d 28-34 knots
A

b

104
Q
What alert must be activated by the D.P.operator if there is a possible risk of
collision?
a Yellow 
b Red
c Green
d None
A

a

105
Q

A diver working from a D.P. controlled vessel is about to operate a H.P. water
jetting gun, which of the following precautions applies?
a The tender takes up the divers slack
b The diver supervisor informs the D.P. operator on the bridge
c The yellow light in dive control is switched on
d The divers platform is recovered to the surface

A

b

106
Q
Horizontal clearance between a suspended mooring line and a deployed bell or
basket,should normally be a minimum of ?
a 100 metres
b 20 metres
c 60 metres
d 50 metres
A

d

107
Q

Define the stages of Gale Warnings.

A

Gale: beaufort scale Force 8, 34‐40 knots
Severe Gale: Force 9, 41‐47 knots
Violent Storm: Force 11, 64 knots or more
Hurricane: Force 12

108
Q

When the wind is Veering, in what direction is it blowing?

A

Clockwise direction.

SW to W exemple

109
Q

When the wind is blowing from SE to NE, what’s the name of it?

A

Backing - Wind in anti clockwise direction.

110
Q

When you hear that the area is expecting a ‘‘Imminent Gale’’, what does it mean?

A

Imminent: within 6h of time
Gale: force 8, wind between 34 - 40 knots

Note: Soon: 6 to 12h
Later: more than 12h

111
Q

Relation to visibility conditions, define the stages of it.

A

Foog: Less than 1000m
Poor: between 1000m and 2nm
Moderate: between 2nm and 5nm
Good: more than 5nm

112
Q

What’s the definition of tides?

A

Is a combination of gravitational effects of the sun and moon.
Rises and Falls every 6h 12min period.

113
Q

What is the difference between ‘‘Spring Tides’’ and ‘‘Neap Tides’’?

A

Spring: When the sun and the moon are aligned and tidal range is at greatest

Neap: When the sun and the moon are at 90⁰ to each other and the tidal range is at lowest.

114
Q

Regards to hazardous areas, zone 2 means?

A

Zone 2: Explosive gas/mixture is unlikely to occur.

note:
Zone 1: Explosive gas/mixture is likely to occur

Zone 0: Explosive gas/mixture always present

115
Q

How many environmental vessel sensors should be online for diving operations?

A
2 anemometers - preferably different locations and supplies cable routes
2 VRU ( vertical reference units) - with separate cable and routes
3 Gyro compasses
116
Q

What is the accuracy of standard deviation for vessel’s positions references?

A

Each of the vessel’s position references should provide position information accurate to ±2% of the water depth. For example in 30m of water the information provided by the reference systems should have a standard deviation of ±0.6m

117
Q

Which reference system should be always online?

A

Radio or Surface reference system.

Always 3 different systems

118
Q

Joystick control is acceptable during diving operations.

True or False

A

False

119
Q

Joystick control is not acceptable during diving operations.

True or False

A

True

120
Q

What is the maximum length of umbilical the diver should have it, if his bailout content last 3min 30sec ?

A

35 meters

note: for every 10 meters the diver should have 1 min of bailout.

121
Q

Explain the causes and types of tides ?

A

Tides are caused by the combination gravitational effects of the sun and moon.

Sun and the moon aligned, tidal range is at greatest - Spring tides
Sun and the moon are 90 degrees to each other tidal range at lowest - Neap tide

122
Q

What is the relation between force exerced on a diver and water current velocity?

A

The current is proporcional to the water velocity squared.

If the velocity doubles, the force increases 4 times

123
Q

When you hear that will be a soon near gale, what is that means?

A

Soon means between 6h and 12h weather

Near Gale is wind force 7 speed between 28 and 33 knots

124
Q

How might HP water jetting affects a DP DSV position system?

a) noise and bubbles may affect HPR system
b) hose may get into thrusters
c) jet could damage ships hull
d) hoses may foul divers umbilical

A

a) noise and bubbles may affect HPR system

125
Q

How close can a vessel approach a platform before permission is required from OIM to come closer?

a) 100m
b) 500m
c) 1500m
d) 2400m

A

b) 500m

126
Q

A DP alert would be given when thruster power output exceeds ?

a) 100%
b) 50%
c) 70%
d) 80%

A

d) 80%

127
Q

A vessel has a draft of 5m and thrusters 20m from the diving deployment point. The wet bell is at 40msw. What’s the maximum length of umbilical would you allow paid out?

a) 20m
b) 25m
c) 35m
d) 40m

A

d) 35m

Square 20 + square 40= minus 5 thrusters safety
Minus 5 draft

128
Q

Using the Beaufort scale describe the wind and sea state for Beaufort number 4
and 7.

A

No 4 – Moderate Breeze (11 to 16 knots) Small waves becoming longer (1-1.5 metres)
No 7 – Near Gale (34 to 40 knots) White foam from breaking waves – beginning to be blown in
direction of wind (4.0 – 5.5m)

129
Q

What status is degraded DP alert?

a. Green status
b. Red status with audible alarm
c. Red status
d. Yellow status

A

d

130
Q

A diver is diving to the bottom, the dive basket depth is 30msw,the nearest thruster is 30 meters from the basket wire. What is the divers maximumallowed umbilical length? (take into account the vessel draft of 5msw)

a. 36 meters
b. 34 meters
c. 37.4 meters

A

b

131
Q

During a Red Alert status, the diving supervisor…..

a. Proceed to the muster station and allow the trainee supervisor to take over.
b. Recover the divers as rapidly as possible.
c. Allow the diver to complete his bottom time, then recover him.

A

b

132
Q

Which 2 answers are disadvantages of an Artemis SurfaceReference System?

a. Signal distortion if fixed antenna battery is low.
b. Limited to line of sight use.
c. Disruption caused by aircraft flying overhead.

A

AB

133
Q

What is the main disadvantage of a Taut Wire reference system?

a. Causes the vessel to list to one side.
b. Obstructs the divers launch and recovery ability
c. Obstructs free movement of fish around the vessel.
d. in shallow water it can only move short distances.

A

d

134
Q

When should there be a dedicated voice communication system,
with back up,between the dive supervisor and the bridge?

a. At all times
b. only when there are trainee DP operators onboard.
c. Not a requirement for air diving operations.

A

a

135
Q

if the DP operator, the diving supervisor or the divers have anyconcerns about the safety of the move, the move should be stopped immediatelyand the divers should return to the bell or basket.
It is recommended that the position moves and heading changes should beexecuted in limited steps of between and heading?

a. maximum steps of 10 - 20 metres and maximum heading changes of 20 degrees.
b. maximum steps of 10-15 metres and maximum heading changes of 10 degrees.
c. maximum steps of 5-10 metres and maximum heading changes of 5 degrees.

A

c

136
Q

When can joystick control be used to move a DP vessel duringdiving operations? (more than I correct answer)

a. it is not allowed during diving operations.
b. Only when there are no divers in the water.
c. When the captain is overly experienced.

A

AB

137
Q

What is the minimum number of reference systems to be in
place before diving work can commence?

a. 3, at least 2 should be of different type.
b. Any 3 different types.
c. 4
d. 2

A

a

138
Q

On a Yellow alert the following action should be taken? (morethan I correct answer)

a. after consultation with the DP operator, the diving supervisor will decide whether to
continue orabort the dive. If he has any doubts, he should abort the dive.

b. as far as is practical, the divers should make safe any work or items of equipment that
could pose ahazard;

c. the diving supervisor should instruct the diver to move to a safe location. This may be
the bellweight, bell or basket;

A

ABC

139
Q

On a Yellow alert the following action should be taken? (morethan I correct answer)

a. after consultation with the DP operator, the diving supervisor will decide whether to
continue orabort the dive. If he has any doubts, he should abort the dive.

b. as far as is practical, the divers should make safe any work or items of equipment that
could pose ahazard;

c. the diving supervisor should instruct the diver to move to a safe location. This may be
the bellweight, bell or basket;

A

ABC

140
Q

Which of the following cause an interference with the
Hydroacoustic Position Reference(HPR) system? (more than I correct answer)

a. Thrusters
b. Divers exhaust bubbles
c. Waterjetting

A

BC

141
Q

What is the minimum class requirement of a DP vessel?

a. Class 2
b. Classl 1
c. No class required for air diving.
d. Class 3

A

a

142
Q

Artemis units are safe for Zone 1 use, but should be switched off during radio silence, for wireline or explosive work This should only be done after consultation with the DP operator and diving supervisor.

True or False

A

True