Flight Deck Procedure- FO Flashcards
ELT
Guard closed
EECs
NORM (No ALTN lights)
Electrical panel
-Standby power AUTO
-Utility busses- ON
-Battery- ON
-Bus ties- AUTO
-Generator controls- ON
-Generator drive disc- DRIVE lights illuminated
-APU- As required
Hydraulic panel
-Demand pumps- OFF (SYS FAULT and PRESS illuminated)
-Engine pump switches-ON (PRESS light illuminated)
Emergency lights switch
Arm them- guard closed
Captain’s audio system switch
NORM
Observer’s audio system switch
NORM
Service interphone switch
OFF
Cargo/cabin interphone switch
As needed
Fuel transfer main 1&4 switch
OFF
Fire panel
-All fire switches in
-No BTL DISCH lights
-All fire arm switches OFF / no lights
Engine start panel
-Start switches- IN
-Standby ignition- NORM
-Continuous ignition- OFF
-Auto ignition- SINGLE
-Autostart- ON
Fuel jettison panel
-Fuel jettison selector- OFF
-Fuel jettison nozzle valve switches- OFF no lights
Fuel panel
-All X FEED switches - ON no VALVE lights
-All fuel pump switches- OFF (all PRESS lights illuminated except for override/jettison pumps and main 2 and 3 AFT if APU running)
Anti-Ice panel
-NAI switches AUTO (or OFF if AUTO not installed)
-WAI switch AUTO (or OFF if AUTO not installed)
Windshield protection panel
-Window heat switches- ON no lights
-Windshield wipers- OFF
Center lighting panel
All lights OFF
Supernumerary oxygen switch
Guard closed
Yaw damper switches
ON
Cabin altitude control panel
-Outflow valves- OPEN
-Landing altitude switch- AUTO
-Outflow valve MAN switches- OFF
-Cabin altitude auto selector- NORM
ECS panel
-Flight deck fan- As needed
-All temp selectors- AUTO
-Zone sys fault light- extinguished
-Trim air- ON
-Equipment cooling- NORM
-HI FLOW- OFF
-Aft cargo heat- OFF
Bleed air panel
-Pack SYS FAULT light- extinguished
-Pack control selectors- as needed
-Isolation valve switches- ON no VALVE lights
-Engine bleed air SYS FAULT lights- extinguished
-APU bleed air switch- ON
-Engine bleed air switches- ON (Verify OFF lights illuminated)
Right lighting panel
-All off except for NAV
-LOGO (when night time)
Flight director switch
ON
Select the ______ display
Status
EFIS control panel
Set as needed
ND mode should be MAP
Set TFC to OFF (Should see TCAS OFF on ND)
EVAS
Check for proper position and velcro strip
Oxygen
Test and set to 100%
Source select panel
Flight director source- R
Navigation source selector- FMC R
EIU source selector- AUTO
IRS source selector- R (AUTO if installed)
Air data source selector- R (AUTO if installed)
IN OTHER WORDS, ALL 12 O’ CLOCK
Clock
Set
CRT select panel
Both to NORM
Flight instruments
Check all flight instruments and correct FMAs. The only flags should be TCAS OFF and NO VSPD until V speeds are set
Ground proximity panel
All switches OFF no lights
Landing gear panel
-Gear lever- DOWN
-Alternate flaps selector- OFF
-Alternate flaps arm- OFF
-Alternate gear extend- OFF
Display brightness controls
As needed
EUI selector
AUTO
Heading reference switch
NORM
FMC master selector
L
Upper and lower EICAS
Check primary and secondary EICAS for engine indications and verify no exceedances
Left radio tuning panel
Verify no OFF light
Center radio tuning panel
Verify no OFF light
Observer audio control panel
As needed
Passenger / cabin signs
ON (Seatbelt and no smoking)
Seatbelt sign must be OFF until fueling complete
Autobrakes
RTO
Weather radar panel
-Gain control- CAL (or AUTO if available)
-Antenna TILT - 4 UP (5 UP mountainous terrain)
-System set to L or R (whoever is PF)
-Ground clutter switch- OFF
Radio tuning panel
Set
FO Audio control panel
As desired
Transponder panel
-Set to L or R (whoever is PF)
-Mode to STBY (code 2000 if no ATC code yet)
Printer
Check no fault lights
Seat
Adjust
Rudder pedals
Adjust
