FINISHES Flashcards

1
Q

Is a mortar consisting of cement, sand and water.

A

Stucco / Cement plaster finish

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Is often added to make the mortar easier to work.

A

Hydrated lime

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

This consists grinding down the surface of the concrete a day or two after it is poured using a brick of carborundum, emery or soft natural stone.

A

Rubbed finish

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

This type of finish is obtained by scrubbing or brushing the concrete surface with fiber or wire brushes and water to remove the surface film or mortar leaving the coarse aggregate exposed.

A

Brushed Finish

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Concrete surfaces may be finished by tooling by any of the methods employed for dressing or finishing natural stone.

A

Tooled finish

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Very much the same appearance as that obtained by brushing the concrete while its still green. Produces granulated finish similar to sandstone but not uniform.

A

Sand Blast Finish

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Color is obtained through this finish and not adding coloring material to the mixture. Facing mortar of 1 part Portland cement, 1 1/2 parts sand and 3 parts of special screenings or pebbles of desired color

A

Exposed Aggregate Finish

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

The concrete aggregate is forced below the surface, the surface is then leveled with a straight wood screed and while the concrete is not firmly set, it is given a float finish with straight flat wood.

A

Wood float finish

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

After the concrete aggregate is forced below the surface, the surface is then leveled with a straight wood screed and given a wood float finish. Before it finally sets, the entire surface is steel trowelled.

A

Steel trowelled finish

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

This finish coat is leveled with a straight wood screed, given a wood finish and then steel trowelled.

A

Integral colored cement finish

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

This consists of a topping with a mixture of 1 part cement, 1 part sand and 1 parr finely crushed stone.

A

Granolithic Finish

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

Is a mixture of cement, marble chip aggregates and water laid as a topping or as a wall finish and ground to a fine, smooth surface.

A

Terrazzo finish

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Is manufactured by pressing in moulds a plastic mixture of cement and sand. Surface color of the tile is achieved by the addition of mineral oxide colors.

A

Cement Tile

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

QDE stands for?

A

Quick Drying Enamel

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

A paint that air-dries to a hard, usually glossy, finish, used for coating surfaces that are outdoors or otherwise subject to hard wear or variations in temperature

A

Enamel Paint

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Is a fast-drying paint made of pigment suspended in acrylic polymer emulsion. Uses of plastic resin made of acrylics or polyvinyls instead of rubber.

A

Acrylic Latex Paint

17
Q

Is a two-component water based acrylic epoxy paint that has superior solvent, chemical and stain resistance ideal for concrete floors and properly primed metal surfaces.

A

Rubberized Epoxy Floor Coating

18
Q

Is paint used on automobiles for both protection and decoration purposes. Water-based acrylic polyurethane enamel paint is currently the most widely used.

A

Automotive Paint

19
Q

Is a latex acrylic product that may have a small amount of epoxy in the mix. These products may have better adhesion and durability than standard acrylic paint

A

Epoxy Paint

20
Q

Is a thin coat of joint compound that you can use to repair or smooth damaged walls. Used in repairing a crack, filling a joint, or leveling an area with an existing flat surface.

A

Skim Coat