F-16

Question 0

Where are the ejection sequence valves located on an F-16 dual seat aircraft?

Answer 0

On the back of each seat support, on on each side

Question 1

What are the modes of ejection for an F-16 dual seat aircraft?

Answer 1

NORM
SOLO
AFT

Question 2

What F-16 escape system component keeps the pressure of the gas in the escape system at an acceptably high level?

Answer 2

M53 initiators

Question 3

How are F-16 TDIs actuated?

Answer 3

Gas pressure

Question 4

What dual seat F-16 explosive component fires each seat’s inertia reel initiators?

Answer 4

The RIGHT side JAU-8/A25 ejection control initiator

Question 5

During a dual seat F-16 ejection when the ejection mode valve is set in NORMAL mode and the forward seat ejection handle is pulled, what explosive component fires the forward seat rocket catapult?

Answer 5

An M53 initiator

Question 6

During a dual seat F-16 ejection when the ejection mode selector valve is set in AFT mode and the aft seat ejection handle is pulled, what explosive component is specifically designed to provide an auto sequence to eject the forward seat?

Answer 6

An M53 initiator

Question 7

What tool should you always use to remove the safety wire from a DTA?

Answer 7

Diagonal cutting pliers

Question 8

If DTA line threads are not coated with a light coat of solid film lube, how do you lube them?

Answer 8

Slide the nut back from the tip and apply a thin film of grease to the but threads with a cotton swab

Question 9

To how many pounds should you torque DTA lines?

Answer 9

50-70

Question 10

How do you check DTA max tip length with the DTA ECRL inspection gage set?

Answer 10

Position the -25 inspection gage on the upper surface of the inspection gage containing the DTA

Question 11

For how many minutes can you electrically power an F-16 without cooking air?

Answer 11

30

Question 12

What F-16 canopy jettison explosive component releases the canopy from the canopy actuator?

Answer 12

Canopy Actuator Release Bolt

Question 13

How long are the lanyards attached to the F-16 external canopy jettison initiator handles?

Answer 13

6 feet

Question 14

During dual seat F-16 canopy jettison during seat ejection, what fires the DTA initiators?

Answer 14

Hot gas fired from the M53 initiators through the sequence valves

Question 15

You should cease F-16 canopy maintenance when wind speeds exceed how many knots?

Answer 15

20

Question 16

When performing a dual seat F-16 canopy removal per the TO, how should you fully open the canopy prior to installing the two canopy maintenance supports?

Answer 16

With the external switch

Question 17

What should you check for during F-16 canopy removal?

Answer 17

That the upper and lower roller bearings have freedom of rotation

Question 18

When you install the tension tubes in a dual seat F-16 during canopy installation, what pattern should they form with the canopy in a full up position?

Answer 18

A “V” pattern with the lower point pointing forward and the upper connection pointing aft

Question 19

When installing a dual seat F-16 canopy, at what angle do you stop lowering the canopy before you install the keeper?

Answer 19

When the canopy angle with the longeron is approximately 27 degrees, measured with a protractor

Question 20

After installing a dual seat F-16 canopy, when performing the canopy warning light ops checkout, what action should cause the CANOPY warning light to come on?

Answer 20

Rotating the canopy lock handle to the unlocked position

Question 21

When rigging a dual seat F-16 canopy, what should the hook throat gap measure at all 10 hooks?

Answer 21

.03-.15 inch

Question 22

When troubleshooting an F-16 with the Fault Isolation manual, what section in chapter 2 would you find the fault isolation tree?

Answer 22

Section IV, Fault Isolation Information

Question 23

When troubleshooting an F-16 canopy system, if the canopy warning light stays on with the canopy down and the canopy lock handle verified down, but manually pressing the unlock warning switch and both hook warning switches simultaneously causes the light to go out, what is the first step you should take to correct the problem?

Answer 23

Rig the switches