Dispatch Control Commands (scenario) Flashcards
Log on unit
L
Log on w/ info
LI
Log off unit
LO
Hold for unit
HU
Hold for time
HT
Dispatch, Dispatch En Route, Dispatch On Scene
D, DE, DO
Dispatch = General Dispatch
D / Direct Dispatch to scene not En Route
Dispatch En Route
DE / Dispatched to scene while unit is already En Route
Dispatch On Scene
DO / Dispatched when already at scene
How do you center your map on a specific Unit?
MAPC
How do you add backup to a Unit?
B, BE, BO
Backup, Backup En Route, Backup On Scene.
i.e. 243 is enr to call… 244 keys up with “244 cover”
How do you put a unit On Scene
OS / A
How do you clear a Unit for a scene?
C time
Subject stop
i.e. 242A in contact with white male Bowles and Wadsworth
SS 242A
Traffic Stop
T
Associated Traffic Stop
AT
Putting a Unit Emergent
39
Unit has subject in custody
95
Field Sobriety Test (roadsides)
FST
Unit requesting DATA
DATA
Stacking a Call to a unit
STACK .call unit comment
Cancel Pending Call
CAN
CAN .call Dispo: Comment:
(comment required)
How do you show duplicates of a single call and what order are they closed in?
DUP .call1 .call2
call 1 remains open and call 2 closes
CAD entry screen just duplicate with quick link
How do you assign a unit to another control group? Why would this be necessary?
CONT
A unit heads to another area to help cover call loads
At Other Location
AO
Field Initiate a call
FI
FI Location: Plate: Type: Comment: LocInfo: Service: RPAdd: CompPhone: State:
(Location and type required)
Field Initiate when already En Route
FIE
Same as FI command except that the unit is specified as en route status
Unit busy and unavailable
C6
Adding a comment to CMD Line to the same call
MI
How do you change call information such as address?
CHG
Changes the CALL location vs. CLO changes the Units location.
Unit Contact Information
UC
can be used to put units in a “no status” state
Unit is O.K. On Scene
C4 time
A Unit has completed transport
TRC
Add involved vehicle record
INVV
Unit Returning
XX
Cross Reference Calls
XREF
Unit Requesting Assistance
RA
Re-Open Closed Call
RO .call
Change a Unverified Location
CLV
Incident History Query
IHQ
IHW From: To: Case#: Type: Location: Agency: Services: Group: Area: District: RPName: Phone: RPAdd: PrimeUnit: Dispo: Priority: DispOper: DispTerm: EntryOper: EntryTerm: CaseExsit: Longitude: Latitude: CommentSrch: IncName:
Case History Query
CHQ
CHQ From: To: Type: Location: PrimeUnit: Dispo: Agency: Group: Site:
CHQ case#
(must use full case number)
Unit History Query
UHQ
UHQ From: To: Operators: Vehicles: Radio:
UHQ unit
How do you look up an operator I.D.?
OPERID
List of (Online) Terminals
TERML
Sending a message
MSG …
Forward message to another terminal(s)
FWD
Log message to call history including warrant
LOGM
At the start of the day as a CALL-TAKER, how do you load?
MON ALL
At the start of the day as the POLICE dispatcher how would you load?
MON P
At the start of the day as the FIRE/DATA Dispatcher how would you load?
MON OS AC PR
example… 243A requesting Backup
RA
You want to find a specific Unit on the CAD map. How do you center the Map over Unit
MAPC
251 CR?
RN/CN
RN/CN .call
RN/CN unit
ONLY ON A ALREADY ACTIVE CALL (OVO IF NO CALL ASSIGNED)
251 additional CR?
RNN
RNN .call
RNN unit
Using the command line as a note pad as to not input information any where else
down arrow
How do you change a unit’s location?
CLO Location
CLO .call
CLO unit
Sets the unit(s) on scene to a new location vs CHG changes the CALL location.
i.e. 251 transporting 1 adult female to detox starting miles 12634
TR 251 Location: detox Milage:12634
a new TR command can be used mid transport if location is diverted.
