Cisco - Pass4Sure Flashcards
Which Router port can be used for disk-in-access to the router CLI for management purposes and does not usually pass normal network traffic? A. AUX B. Gigabit Ethernet C. Fast Ethernet D. Channelized Serial
A. AUX
Which two pieces of information does the "show ip interface brief" command display? (Choose Two) A. Encapsulation type B. Interface Status C. Layer 2 address D. Layer 3 address E. Keep alive
B. Interface status
D. Layer 3 address
The pins and RJ-45 are numbered from 1 through 8. With the material points of the plug facing toward you, pin 1 is the leftmost pin. Which two sets are looped on an RJ-45 T1 loopback plug? (choose two) A. Pins 1 and 4 B. Pins 1 and 7 C. Pins 2 and 5 D. Pins 2 and 8 E. Pins 1 and 5 F. Pins 2 and 7
A. Pins 1 and 4
C. Pins 2 and 5
What are two ways to open Microsoft Notepad on a Windows-based computer? (Choose two)
A. Start> Run Enter Notepad and click OK
B. Start> Control Panel> Notepad
C. Start> All Programs> Notepad
D. Start> All Programs> Accessories> Notepad
E. Start> All Programs> Microsoft Office> Notepad
A. Start> Run Enter Notepad and click OK
D. Start> All Programs> Accessories> Notepad
Which three of the following statements are true? (Choose three)
A. Each IP address has two parts: a network ID and a host ID
B. An IP subnet equals a broadcast domain.
C. An IPv4 address contains 36 bits
D. 172.16.1.18 is a class A address
E. A subnet address is created by borrowing bits from the original host ID
A. Each IP address has two parts: a network ID and a host ID.
B. An IP subnet equals a broadcast domain.
E. A subnet address is created by borrowing bits from the original host ID.
Which of the following is a DTE device? A. router B. CSU/DSU C. Cable Modem D. DSL modem
A. router
Which two of the following statements are true about a switch? (choose two)
A. It is a repeater
B. It is a data link layer device.
C. It will forward the frame out all ports when it receives a broadcast from a host.
D. It reads the destination MAC address to forward traffic out the appropriate port.
E. it acts as an amplifier.
B. It is a data link layer device.
D. It reads the destination MAC address to forward traffic out the appropriate port.
Which of the following best describes the cable that is used to connect a laptop to an ethernet port on a Cisco router? A. Crossover B. Straight-through C. Fiber D. Rollover
A. Crossover
What are two features that are associated with single-mode fiber-optic cable? (Choose two)
A. a single strand of glass fiber
B. carries higher bandwidth than multimode fiber
C. costs is less than multimode fiber
D. operates over less distance than multimode fiber
A. a single strand of glass fiber
B. carries higher bandwidth than multimode fiber
Which layer of the OSI model defines how data is formated for transmission and how access to the physical media is controlled A. physical B. Data link C. Network D. Transport
B. Data link
Which type of memory is used to permanently store the Cisco IOS software A. Flash B. DRAM C. SRAM D. NVRAM
A. Flash
What is the default operating mode you are initially logging into a router? A. global configuration B. privileged EXEC C. ROM monitor D. user EXEC
D. user EXEC
What two of the following are components of a WAN connection? (Choose Two) A. Router B. Switch C. CSU/DSU D. Hub E. Bridge
A. Router
C. CSU/DSU
A null modem cable uses which adapter type? A. RJ-11 B. RJ-45 C. RS-323 D. RS-232 E. USB
B. RJ-45
TFTP is a simple protocol file such as a Cisco IOS or configuration file from one device to another. Which device cannot be configured to be used as a TFTP server? A. Cisco Router B. Cisco Switch C. Computer D. Modem E. Cisco wireless LAN
D. Modem
Which command sends an echo request packet to the largest host and then waits for an echo response message? A. Telnet B. connect C. access D. echo E. ping
E. ping
Which layer facilitates the routing of packets over an IP network? A. MAC B. transport C. network D. physical
C. network
Which command can be used to identify the serial number of a cisco router? A. Show run B. Show version C. Show Archive D. Show enviroment
B. Show version
while performing password recovery on a cisco device, the configuration register should be which value in order to bypass loading the startup configuration? A. 0x2102 B. 0x2112 C. 0x2122 D. 0X2142
D. 0X2142
Which three of the following statements are true about a router? (Choose Three)
A. It forwards broadcast frames
B. It interconnectes multiple networks together
C. It chooses the best route for your data to travel
D. it manages and analyzes a company’s database
E. It divides a network into seperate broadcast domains.
B. It interconnectes multiple networks together
C. It chooses the best route for your data to travel
E. It divides a network into seperate broadcast domains.
Which IOS layer does a server use to keep track of which application communications in which conversation? A. Transport B. Network C. Session D. Application
C. Session
Which command initiates copying the saved configuration of a Cisco device to a TFTP server? A. Copy running-config tftp B. Copy startup-config tftp C. Copy tftp running-config D. Copy tftp startup-config
B. Copy startup-config tftp
Which Windows-based text editor is preferred when working with a simple text document such as a Cisco configuration A. Microsoft Excel B. Microsoft Word C. Microsoft Notepad D. Microsoft Access
C. Microsoft Notepad
Which of the following best describes the port on a laptop that is used to connect to an Ethernet port on a Cisco Switch A. RJ-45 B. RJ-11 C. VGA D. DVI E. DB-9
A. RJ-45
Pin 1 connected to Pin 8 is an example of a A. RJ-45 straight through B. RJ-45 C. RJ-45 rollover D. RJ-11 E. RJ-45 crossover
E. RJ-45 crossover
Which of the following best describes how to assign a static IP address to the Ethernet port on a computer?
A. From network connections, click Create a New Connection and follow the network connection Wizard instructions.
B. From the Network Connections, double-click Local Area Connection. Click Protocol (TCP/IP). Click the properties, click the “Use the following address” button, and then configure the IP information.
C. Click Start> Run Enter cmd and click OK. Enter ip address XXX.XXX.XXX.XXX
D. From Network Connections, Double-Click Local Connection. Click Properties, click iPass Protocol (IEEE), Click properties and select static IP.
B. From the Network Connections, double-click Local Area Connection. Click Protocol (TCP/IP). Click the properties, click the “Use the following address” button, and then configure the IP information.
On which three operating systems does HyperTerminal not come pre-installed? (Choose Three) A. Windows XP B. Windows Vista C. Mac OSX D. Windows 98 E. Windows 7 F. Windows 2000
B. Windows Vista
C. Mac OSX
E. Windows 7
Which three of the following describe Fast Ethernet? (choose three)
A. 1QBASE-T H B
B. 100BASE-T
C. 10-Mb/s speed
D. 100-Mb/s speed
E requires Category 3 or higher UTP cabling
F. requires Category 5 or higher UTP cabling
B. 100BASE-T
D. 100-Mb/s speed
F. requires Category 5 or higher UTP cabling
Which bits represent the boot field in the configuration register value? A. highest two bits B. highest four bits C. lowest two bits D. lowest four bits
D. lowest four bits
At the interface configuration prompt, which command returns you to the main configuration prompt? A. Ctrl-Z B. end C. exit D. quit
C. exit
Which port displays the bootup process on a cisco device? A. ATM B. BVI C. Console D. Ethernet
C. Console
What is the correct sequence to configure Fastethernet0 from EXEC mode
Enable
Configure Terminal
interface fastethernet0
which type of memory stores the startup configuration file for the cisco device? A. Flash B. NVRAM C. RAM D. ROM
B. NVRAM
Which commmand initiates the copy of an IOS image to a Cisco device? A. copy flash tftp B. copy tftp flash C. copy tftp ftp D. copy tftp nvram E. xmodem flash
B. copy tftp flash
When using a modem to provide out-of-band access to a Cisco router, which cable is used to connect the modem to the router? A. DB-25 to RJ-45 B. RJ45 to RJ-45 C. RJ-44 to RJ-45 D. DB-9 to RJ-45 E. DB-45 to RJ-45
A. DB-25 to RJ-45
Which two of the following are installed fiber-optic connectors? (Choose two) A. Suscriber B. Crossover C. multi-dimension D. Lucent
A. Suscriber
D. Lucent
Which two pairs of LAN Ethernet devices use an RJ-45 Straight-Through cable? (Choose two) A. Switch to switch B. Switch to router C. Switch to Server D. Router to router E. Switch to Hub
B. Switch to router
C. Switch to Server
Which type of memory stores the decompressed form of the Cisco IOS software and the running configuration? A. Flash B. ROM C. DRAM D. NVRAM
C. DRAM
When using a modem to provide out-of-band access to a cisco router, which cable type is used to connect the wall jack to the modem? A. DB-25 to RJ-11 B. RJ11 to RJ-11 C. RJ-45 to RJ-45 D. RJ-11 to RJ-45 E. RJ-11 to DB-9
B. RJ11 to RJ-11
Which 3 of the following statements are true about a smart jack? (Choose 3)
A. It provides signal conversion.
B. It operates at Layer 2 of the OSI model
C. It regenerates the signal to compensate for signal degradation from the line transmission
D. It Provides Loopback testing.
E. It acts as a concentration point for dial-in and dial-out connections
A. It provides signal conversion.
C. It regenerates the signal to compensate for signal degradation from the line transmission
D. It Provides Loopback testing.
Which interface card is an encryption module? A. NME-VMSS-16 B. NME-CUSP-552 C. AIM-VPN/SSL-3 D. M-1A-OC3-POM
C. AIM-VPN/SSL-3
SSL
Which two of the following CLI operating modes, by default, allow you to copy a Cisco IOS image to flash memory from TFTP server? (Choose Two) A. User Exec B. Priviledge EXEC C. ROMMON D. Global configuration
B. Priviledge EXEC
C. ROMMON
Which three pieces of information about a device can be seen from the show version command? (Choose three) A. CPU load B. Device Model C. Installed DRAM D. Installed Flash E. Locally configured IP addresses
B. Device Model
C. Installed DRAM
D. Installed Flash
Which Two Commands display the saved configuration file? (Choose two) A. Show configuration B. Show file system C. Show Running-config D. Show startup-config
A. Show configuration
D. Show startup-config
Which two of the following statements are true? (Choose Two)
A. OEM products that are built for Cisco never get a Cisco logo applied.
B. The Cisco logo, old or new, can be found on the front bezel of all Cisco rack-mountable or desktop products.
C. Serical numbers are attached by a label on all Cisco field-replaceable parts.
D. At the network module level, the model number is the same as the part number
B. The Cisco logo, old or new, can be found on the front bezel of all Cisco rack-mountable or desktop products. D. At the network module level, the model number is the same as the part number
What does Cisco use for Return Materials Authorization (RMA) tracking of field replaceable parts? A. Model number B. Product number C. Serial number D. RMA number E. FRU number
D. RMA number
Which command initiates the transfer of a cisco IOS image over IP from ROMMON A. copy tftp: flash: B. copy flash: tftp: C. tftpdnld D. xmodem
C. tftpdnld
ESD is the sudden and momentary electric current that flows between two different objects at different electrical potentials caused by direct contact or induced by and electrostatic field. Which three of the following tools should be used to avoid ESD (choose three) A. ESD wrist strap B. Latex gloves C. Antistatic bag D. Antistatic mat E. Negitive Static mat F. Negitive static bag
A. ESD wrist strap
C. Antistatic bag
D. Antistatic mat
Which command indicates the amount of memory (NVRAM, RAM, and flash) in a Cisco Device? A. Show diag B. Show enviroment C. Show inventory D. Show version
D.Show version
Which two of the following are true? (choose two)
A. Telnet is preferred over SSH for security reasons.
B. SSH is a protocol that provides a secure remote access connection to the network devices.
C. When using HyperTerminal to communicate over a TCP/IP netowrk, the SSH protocol is used.
D. A Telnet network management connection is dropped when a router reboots
E. Telnet is a protocol that provides a secure remote access connection to network devices
B. SSH is a protocol that provides a secure remote access connection to the network devices.
D. A Telnet network management connection is dropped when a router reboots
The colored wire at one end of the cable in the reverse sequence of the colored wires at the other end of the cable. What cable does this describe? A. Rolled B. Coaxial C. Crossover D. Straight-Through
A. Rolled
Which of the following are features of NVRAM on a Cisco device? (Choose Two) A. Stores startup configuration B. Stores running configuration C. Stores routing tables D. Erased when device is rebooted F. Not erased when device is rebooted
A. Stores startup configuration
F. Not erased when device is rebooted
Which command displays the configuration register setting? A. Show config-register B. Show flash C. Show running-config D. show version
D. show version
Which two of the following statements are true? (choose two)
A. Because FTP usually requires authentication, a Cisco router must be configured with the appropriate username and password.
B. FTP uses UDP as its transport protocol.
C. The copy running-config ftp: command is used to copy a configuration file from an FTP server to the running configuration.
D. A router can act as an FTP server.
E. FTP can be used to load Cisco IOS software to router in ROMMON mode.
A. Because FTP usually requires authentication, a Cisco router must be configured with the appropriate username and password.
D. A router can act as an FTP server.
From a Windows command prompt, which command displays the local IP address of a computer? A. ip config B. ip configuration C. ipconfig d. ipconfiguration
C. ipconfig
Which of the following best describes the cable that is used to connect a laptop to the Console port on a Cisco router? A. Crossover B. Straight-Through C, Fiber D. Rollover
D. Rollover
What are two possible causes if an Ethernet interface is up and the line protocol is down (choose two)
A. The Ethernet cable might not be attached properly.
B. There is a speed or duplex mismatch with the remote device
C. The ethernet interface has been manually disabled.
D. There is a Layer 2 mismatch in the encapsulation type
E. Keepalives are not being received by the local device.
B. There is a speed or duplex mismatch with the remote device
D. There is a Layer 2 mismatch in the encapsulation type
Which type of memory is necessary for a router to boot? A. DRAM B. PVDM C. NVRAM D. VRAM
A. DRAM
Which two pieces of information can be determined about a neighbor device from the CLI command "show cdp neighbor"? (Choose two) A. device ID B. IP address C. platform D. uptime
A. device ID
C. platform
Which two modules can be plugged into internal advanced integration module (AIM) slots on a Cisco router? (Choose two)
A. Virtual Private Network Module
B. Intrusion Detection System Module
C. Packet Voice Digital Signal Processor Module
D. LAN Switching Module
E. Voice Interface Module
A. Virtual Private Network Module
B. Intrusion Detection System Module
Which two commands are used to set the configuration register value? (choose two)
A. Router(config)#config-register 0x2102
B. Router(config)#confreg 0x2102
C. rommon> config-register 0x2102
D. rommon> confreg 0x2102
E. Router(config)#configuration-register 0x2102
A. Router(config)#config-register 0x2102
D. rommon> confreg 0x2102
What are two ways to open a command prompt session on a Windows-based computer? (Choose two)
A. Click Start > Control Panel > Command Prompt
B. Click Start > All Programs > Accessories > Command Prompt
C. Click Start > All Programs > Command Prompt
D. Click Start > Run. Enter cmd and click OK
E. Click Start > All Programs > Accessories > Communications > Command Prompt.
B. Click Start > All Programs > Accessories > Command Prompt
D. Click Start > Run. Enter cmd and click OK
