Chapter 5 & 6 Flashcards

1
Q

How can you set increment/decrement nudge values

A

Hold Option + Shift

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

How do you change nudge values?

A

Hold Command + Option and press +/- on the numeric keyboard

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

How can you nudge a single clip or multiple clips?

A
  1. Select the clip/Clips with the Grabber tool
  2. Press +/- On the numeric keypad
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

How can you nudge an edit selection?

A

Press shift followed by the +/- button on the numeric keypad

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

How do you nudge the start time of a selection?

A

Press Option + Shift and the +/- Key on the numeric keypad

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

How do you nudge the end time of a selection?

A

Press Command + Shift and the +/- Key on the numeric keypad

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

How do you trim with Nudge?

A
  1. Configure nudge value to small increment (10msec or 1 frame)
  2. Select clip you want to trim
  3. (For Start) Hold Option and Press +/- on numeric keypad
  4. (For End) Hold Command and Press +/- on numeric keypad
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

How do you nudge the contents of a clip without changing the clips start and end points?

A
  1. Configure nudge value
  2. Select clip whose contents you want to nudge
  3. Hold “Control” and press +/- On numeric keypad
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Whats the difference between the shift command and nudging?

A
  1. The shift command allows you to specify a different offset each time you use it. Nudging always uses the nudge increment value
  2. Shift command will separate a clip at the selection boundaries if used on a partial clip. Nudging on a partial clip will move the selection, leaving the underlying media changed.
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

How can you open the shift dialogue box?

A

Option + H or Edit > SHIFT

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

How can you duplicate a selection while extending the selection to the end of the duplicate?

A
  1. Edit > Selection > Duplicate and extend edit
  2. Command + Option + Control + Shift + D
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

How can you scrub using Shuttle mode?

A
  1. With scrubber tool selected press “option” then click and hold on any track.
  2. While holding drag left or right to begin scrubbing
  3. To Increase speed move further left or right.
  4. Release the mouse to stop playback
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

How do you set values for pre and post roll auditioning?

A
  1. Specify the Pre and post roll values in the transport window
  2. Click and drag the pre and post roll flags in the main timebase ruler to set durations for each
  3. Using the selector tool option click in the edit playlist before and after a selection to set the desired durations.
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

How do you enable commands keyboard focus mode?

A
  1. Click A-Z button in upper right corner of the edit window.
  2. Press Command + Option + 1
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

How can you access the Strip Silence window?

A

Choose Edit > Strip Silence OR Command + U

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

How do you add a sync point to a clip?

A
  1. Place edit cursor inside clip where you want sync point to occur.
  2. With cursor in position choose Clip > Identify sync point OR Command+
17
Q

How does a sync point appear?

A

As a small inverted triangle at the bottom of a clip

18
Q

How do you align a clips start?

A

Control click to be aligned, with grabber tool.

19
Q

How do you align a clips end?

A

Control + Command and click on the clip you wish to move with the grabber tool.

20
Q

How do you align to a clips sync point?

A

Control + Shift and click on the clip containing the sync point with the grabber tool