Chapter 4 Flashcards

1
Q
What type of power flaw involves a fluctuation in voltage levels caused by other devices on the network or by EMI?
A) brownout
B) blackout
C) noise
D) surge
A

C) noise

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q
One watt is equal to how many volt-amps?
A) 1.4
B) 2
C) 10
D) 1,000
A

A) 1.4

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q
What is the maximum allowable distance for horizontal wiring?
A) 100 ft
B) 100 m
C) 90 m
D) 90 ft
A

B) 100 m

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q
The radius of the maximum arc into which you can loop a cable without impairing data transmission is known as what option below?
A) metal stress factor
B) arc coefficient
C) bend radius
D) flex rating
A

C) bend radius

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q
How far away from fluorescent lights or other sources of EMI should cable be installed?
A) at least 3 ft
B) at least 5 ft
C) at least 10 ft
D) at least 20 ft
A

A) at least 3 ft

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q
What is the industry standard for rack height in rack units?
A) 18U
B) 22U
C) 42U
D) 54U
A

C) 42U

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q
Which method of transmission allows signals to travel in both directions over a medium simultaneously?
A) half duplex
B) simplex
C) full-duplex
D) multiplex
A

C) full-duplex

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q
Which method of transmission allows signals to travel in both directions over a medium but in only one direction at a time?
A) full duplex
B) half duplex
C) simplex
D) multiplex
A

B) half duplex

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q
Ethernet exists at what layer of the OSI model?
A) Layer 1
B) Layer 2
C) Layer 3
D) Layer 4
A

B) Layer 2

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q
What is the maximum frame size for Ethernet ll frames on a VLAN?
A) 1500 bytes
B) 1518 bytes
C) 1522 bytes
D) 1496 bytes
A

C) 1522 bytes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q
When selecting a punch down block, what block type is more suitable for data connections?
A) 10 block
B) 22 block
C) 66 block
D) 110 block
A

D) 110 block

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q
What component of the backbone runs between a building's floors and can be used to connect an MDF and IDF or multiple IDFs?
A) horizontal cross connect
B) patch cable
C) vertical cross connect
D) diagonal cabling
A

C) vertical cross connect

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

Where is a demarc located in relation to the structured cabling of an enterprise environment?
A) in the Main Distribution Frame (MDF)
B) at the Intermediate Distribution Frame (IDF)
C) in the work area
D) between the MDF and the IDF

A

A) in the Main Distribution Frame (MDF)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q
Select the component of enterprise level structured cabling that serves as the location where an incoming network interface enters a building and connects with the building's backbone cabling:
A) network interface device
B) main distribution frame
C) intermediate distribution frame
D) entrance facility
A

D) entrance facility

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

During termination of twisted pair cabling, what should be done to ensure minimal cross talk is introduced?
A) No more than 1 inch of the cable should be exposed
B) No less than 1 inch of the cable should be exposed
C) Each pair should be stripped of insulation so that it doesn’t get caught in the jack
D) Each pair should be twisted around another pair to reduce cross talk

A

A) No more than 1 inch of the cable should be exposed

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q
What cable type comes in two different modes, single mode and multimode?
A) UTP
B) STP
C) Fiber Optic
D) Coaxial
A

C) Fiber Optic

17
Q
Which of the following options is not a likely source of electromagnetic interference?
A) power lines
B) motors
C) fiber optic cables
D) microwaves
A

C) fiber optic cables

18
Q
In order to simplify console access to computers in a rack, what device is typically used to provide a central portal for all devices on the rack?
A) KVM switch
B) AVR switch
C) terminal server
D) multi-monitor breakout cable
A

A) KVM switch

19
Q
If the use of a pre-existing Ethernet infrastructure is desired for a SAN, what Transport Layer protocol should be utilized?
A) Fibre Channel
B) iSCSI
C) SAS
D) PATA
A

B) iSCSI

20
Q
What type of power converter changes the voltage of an AC current, such as when power over the main line from an electric company is changed before being delivered to a home?
A) inverter
B) rectifier
C) transformer
D) voltage regulator
A

C) transformer

21
Q
Select the two terms below that are used to describe a UPS that provides continuous voltage to a device by switching virtually instantaneously to the battery when it detects a loss of power;
A) offline UPS
B) standby UPS
C) standby power supply
D) failover power supply
A

B) standby UPS

C) standby power supply

22
Q

The standard that describes uniform, enterprise-wide cabling systems, regardless of who manufactures or sells the various parts used in the system, can be referred to by what two options below?
A) hierarchical cabling
B) TIA/EIA-568
C) IEEE Commercial Building Wiring Standard
D) structured cabling

A

B) TIA/EIA-568

D) structured cabling

23
Q
Equipment racks most commonly come in what two widths?
A) 17 in frame
B) 18 in frame
C) 19 in frame
D) 23 in frame
A

C) 19 in frame

D) 23 in frame

24
Q
Select the two Transport Layer protocol that are used by SANs: 
A) Fibre Channel
B) iSCSI
C) SAS
D) SATA
A

A) Fibre Channel

B) iSCSI

25
Q
Select the maximum allowable distances for horizontal  wiring for a span that connects a data jack on a wall to a data closet, and for a span that connects a workstation to the data jack, respectively:
A) 100 m
B) 90 m
C) 10 m
D) 5 m
A

B) 90 m

C) 10 m