CCT Assessment 2 Flashcards
Which port on a router can be used for disk-in access to the router CLI management purposes and does not usually pass normal network traffic
AUX
Which two pieces of information does the show ip interface brief command display? (Choose two)
A. Encapsulation type
B. Interface status
C. Layer 2 address
D. Layer 3 address
E. Keep alive
Interface status
Layer 3 address
The pins and RJ-45 are numbered from 1 through 8. With the material points of the plug facing toward you, pin 1 is the leftmost pin. Which two sets are looped on an RJ-45 T1 loopback plug? (Choose two)
A. Pins 1 and 4
B. Pins 1 and 7
C. Pins 2 and 5
D. Pins 2 and 8
E. Pins 1 and 5
F. Pins 2 and 7
Pins 1 and 4
Pins 2 and 5
What are two ways to open Microsoft Notepad on a Windows-based computer? (Choose two)
A. Start > Run Enter Notepad and Click OK
B. Start > Control Panel > Notepad
C. Start > All Programs > Notepad
D. Start > All Programs > Accessories > Notepad
E. Start > All Programs > Microsoft Office > Notepad
Start > Run Enter Notepad and Click OK
Start > All Programs > Accessories > Notepad
Which three of the following statements are true? (Choose three.)
A. Each IP address has two parts: a network ID and a host ID
B. An IP subnet equals a broadcast domain.
C. An IPv4 address contains 36 bits
D. 172.16.1.18 is a Class A address
E. A subnet address is created by borrowing bits from the original host ID
Each IP address has two parts: a network ID and a host ID
An IP subnet equals a broadcast domain.
A subnet address is created by borrowing bits from the original host ID
Which of the following is a DTE device?
router
Which two of the following statements are true about a switch? (Choose two)
A. It is a repeater.
B. It is a data link layer device.
C. It will forward the frame out all ports when it receives a broadcast from a host.
D. It reads the destination MAC address to forward traffic out the appropriate port.
E. It acts as an amplifier.
It is a data link layer device.
It reads the destination MAC address to forward traffic out the appropriate port.
Which of the following best describes the cable that is used to connect a laptop to an Ethernet port on a Cisco router?
crossover
Which type of cable is used on the ATM card?
Coaxial
What are two features that are associated with single-mode fiber-optic cable? (Choose two.)
A. a single strand of glass fiber
B. carries higher bandwidth than multimode fiber
C. cost is less than multimode fiber
D. operates over less distance than multimode fiber
a single strand of glass fiber
carries higher bandwidth than multimode fiber
Into which port do you insert the card?
Gigabit Ethernet
Which layer of the IOS model defines how data is formatted for transmission and how access to the physical media is controlled?
Data link
Which type if memory is used to permanently store the Cisco IOS software?
Flash
What is the default operating mode you are initially logging into a router?
user EXEC
Which two of the following are component of WAN connection? (Choose two)
A. router
B. switch
C. CSU/DSU
D. Hub
E. Bridge
router
CSU/DSU
A null modem cable uses which adapter type?
RS-232
TFTP is a simple protocol files, such as a Cisco IOS or configuration file, from one device to another. Which device cannot be configured to be used as a TFTP server?
Modem
Which command sends an echo request packet to the largest host and then waits for an echo response message?
ping
Which address facilitates the routing of packets over an IP network?
network
Which command can be used to identify the serial number of a Cisco router?
show version
While performing password recovery on a Cisco device, the configuration register should be which value in order to bypass loading the startup configuration?
0x2142
Which three of the following statements are true about a router? (Choose three)
A. It forwards broadcast frames.
B. It interconnects multiple networks together.
C. It chooses the best route for your data to travel.
D. It manages and analyzes a company’s database.
E. It divides a network into separate broadcast domains.
It interconnects multiple networks together.
It chooses the best route for your data to travel.
It divides a network into separate broadcast domains.
Which IOS layer does a server use to keep track of which application communications in which conversation?
Session
Which command initiates copying the saved configuration of a Cisco device to a TFTP server?
copy startup-config tftp
Which windows-based text editor is preferred when working with a simple text document such as a Cisco configuration?
Microsoft Notepad
Which of the following best describes the port on a laptop that is used to connection to an Ethernet port on a Cisco Switch?
RJ-45
Of which cable type is this an example?
RJ-45 crossover
Which of the following best describes how to assign a static IP address to the Ethernet port on a computer?
From Network Connections, double-click Local Area Connection. Click Protocol (TCP/IP). Click the properties, click the use the Following Address button, and then configure the IP information.
On which three operating systems does HyperTerminal not come pre-installed? (Choose three)
A. Windows XP
B. Windows Vista
C. Mac OSX
D. Windows 98
E. Windows 7
F. Windows 2000
Windows Vista
Mac OSX
Windows 7
Which three of the following describe Fast Ethernet? (Choose three)
A. 1QBASE-T H B
B. 100BASE-T
C. 10-Mb/s speed
D. 100-Mb/s speed
E. requires Category 3 or higher UTP cabling
F. requires Category 5 or higher UTP cabling
100BASE-T
100-Mb/s speed
requires Category 5 or higher UTP cabling
You are performing a password recovery on a Cisco fixed Catalyst Switch. Drag the appropriate Steps to the correct order.
step 1 power on
step 2 mode button
step 3 flash_init
step 4 load_helper
Which bits represent the boot field in the configuration register value?
D. lowest four bits
At the interface configuration prompt, which command returns you to the main configuration prompt?
exit
Which port displays the bootup process on a Cisco device?
Console
Drag the CLI Commands in the proper sequence to configure FastEthernet0 from user EXEC mode.
step 1 enable
step 2 configure terminal
step 3 interface fastethernet0
Which type of memory stores the startup configuration file for the Cisco device?
B. NVRAM
Which command initiates the copy of an IOS image to a Cisco device?
copy tftp flash
When using a modem to provide out-of-band access to a Cisco router, which cable is used to connect the modem to the router?
DB-25 to RJ-45
Which two of the following are installed fiber-optic connectors? (Choose two)
A. subscriber
B. crossover
C. multi-dimension
D. Lucent
subscriber
Lucent
Which two pairs of LAN Ethernet devices use an RJ-45 Straight-through cable? (Choose two)
A. Switch to switch
B. Switch to router
C. Switch to server
D. Router to router
E. Switch to hub
Switch to router
Switch to server
Which type of memory stores the decompressed form of the Cisco IOS software and the runningconfiguration?
DRAM
When using a modem to provide out-of-band access to a Cisco router, which cable type is used to connect the wall jack to the modem?
B. RJ-11 to Rj-11
Which three of the following statements are true about a smart jack? (Choose three)
A. It provides signal conversion.
B. It operates at Layer 2 of the OSI model.
C. It regenerates the signal to compensate for signal degradation from line transmission.
D. It provides loopback testing.
E. It acts as a concentration point for dial-in and dial-out connections.
It provides signal conversion.
It regenerates the signal to compensate for signal degradation from line transmission.
What does the CD LED indicate on the voice WAN interface card?
A carrier has been detected
Which interface card is an encryption module?
AIM-VPN/SSL-3
Which two of the following CLI operating modes, by default, allow you to copy a Cisco IOS image to flash memory from TFTP server? (Choose two)
A. User EXEC
B. Privileged EXEC
C. ROMMON
D. Global configuration
Privileged EXEC
ROMMON
Which three pieces of information about a device can be seen from the show version command? (Choose three)
A. CPU load
B. Device model
C. Installed DRAM
D. Installed flash
E. Locally configured IP addresses
Device model
Installed DRAM
Installed flash
Which two commands display the saved configuration file? (Choose two)
A. show configuration
B. show file system
C. show running-config
D. show startup-config
show configuration
show startup-config
Which two of the following statements are true? (Choose two)
A. OEM products that are built for Cisco never get a Cisco logo applied.
B. The Cisco logo, old or new, can be found on the front bezel of all Cisco rack-mountable or desktop products.
C. Serial numbers are attached by label on all Cisco field-replaceable parts.
D. At the network module level, the model number is the same as the part number.
The Cisco logo, old or new, can be found on the front bezel of all Cisco rack-mountable or desktop products.
At the network module level, the model number is the same as the part number.
What does Cisco use for Return Materials Authorization (RMA) tracking of field-replaceable parts?
RMA number
Which command initiates the transfer of a Cisco IOS image ROMMON?
tftpdnld
ESD is the sudden and momentary electric current that flows between two different objects at different electrical potentials caused by direct contact or induced by an electrostatic field. Which three of the following tools should be used to avoid ESD? (Choose three)
A. ESD wrist strap
B. Latex gloves
C. Antistatic bag
D. Antistatic mat
E. Negative static mat
F. Negative static bag
ESD wrist strap
Antistatic bag
Antistatic mat
Which command indicates the amount of memory (NVRAM, RAM, and flash) in a Cisco device?
show version
Which two of the following are true? (Choose two)
A. Telnet is preferred over SSH for security reasons.
B. SSH is a protocol that provides a secure remote access connection to network devices.
C. When using HyperTerminal to communicate over a TCP/IP network, the SSH protocol is used.
D. A Telnet network management connection is dropped when a router reboots.
E. Telnet is a protocol that provides a secure remote access connection to network devices.
SSH is a protocol that provides a secure remote access connection to network devices.
A Telnet network management connection is dropped when a router reboots.
The colored wires at one end of the cable in the reverse sequence of the colored wires at the other end of the cable. Which cable does this describe?
Rolled
Which two of the following are features of NVRAM on a Cisco device? (Choose two)
A. Stores startup configuration
B. Stores running configuration
C. Stores routing tables
D. Stores decompressed IOS software image
E. Erased when device is rebooted
F. Not erased when device is rebooted
Stores startup configuration
Not erased when device is rebooted
Which command displays the configuration register setting?
show version
Which two of the following statements are true? (Choose two)
A. Because FTP usually requires authentication, a Cisco router must be configured with the appropriate username and password.
B. FTP uses UDP as its transport protocol.
C. The copy running-config ftp: command is used to copy a configuration file from an FTP server to the running configuration.
D. A router can act as an FTP server.
E. FTP can be used to load Cisco IOS software to router in ROMMON mode.
Because FTP usually requires authentication, a Cisco router must be configured with the appropriate username and password.
A router can act as an FTP server.
From a Windows command prompt, which command displays the local IP address of a computer?
ipconfig
Which of the following best describes the cable that is used to connect a laptop to the Console port on a Cisco router?
rollover
What are two possible causes if an Ethernet interface is up and the line protocol is down? (Choose two)
A. The Ethernet cable might not be attached properly
B. There is a speed or duplex mismatch with the remote device
C. The Ethernet interface has been manually disabled
D. There is a Layer 2 mismatch in the encapsulation type
E. Keepalives are not being received by the local device
There is a speed or duplex mismatch with the remote device
There is a Layer 2 mismatch in the encapsulation type
Which type of memory is necessary for a router to boot?
DRAM
Which two pieces of information can be determined about a neighbor device from the CLI command show cdp neighbor? (Choose two)
A. device ID
B. IP address
C. platform
D. uptime
device ID
platform
Which two modules can be plugged into internal advanced integration module (AIM) slots on a Cisco router? (Choose two)
A. Virtual Private Network Module
B. Intrusion Detection System Module
C. Packet Voice Digital Signal Processor Module
D. LAN Switching Module
E. Voice Interface Module
Virtual Private Network Module
Intrusion Detection System Module
Which two commands are used to set the configuration register value? (Choose two)
A. Router(config)#config-register 0x2102
B. Router(config)#confreg 0x2102
C. rommon>config-register 0x2102
D. rommon>confreg 0x2102
E. Router(config)#configuration-register 0x2102
Router(config)#config-register 0x2102
rommon>confreg 0x2102
What are two ways to open a command prompt session on a Windows-based computer? (Choose two)
A. Click Start > Control Panel > Command Prompt
B. Click Start > All Programs > Accessories > Command Prompt
C. Click Start > All Programs > Command Prompt
D. Click Start > Run. Enter cmd and click OK
E. Click Start > All Programs > Accessories > Communications > Command Prompt
Click Start > All Programs > Accessories > Command Prompt
Click Start > Run. Enter cmd and click OK
What type of memory contains the basic code for booting a device and maintaining POST, ROMmon, bootstrap, and RXBOOT?
ROM
What type of memory is nonvolatile and contains the Cisco IOS image?
Flash
This type of memory contains the running IOS and the running configuration (active configuration) that is used after a machine is booted.
RAM
This type of memory stores the startup configuration.
NVRAM
What type of cable would you connect to manage your Cisco device from the COM port of your PC?
Rollover cable
Which are two methods of exiting out of Setup Mode? (Choose 2.)
A. Ctrl+C
B. Ctrl+Z
C. Answer no
D. Type end
Ctrl+C
Answer no
You have just been given a router that will not save its configuration. As you boot up the router, you confirm that despite saving the configurations several times, the router enters Setup Mode consistently. What might be a possible cause?
The configuration register is 0x2142.
Assuming no boot commands, what is the default location of the IOS and what is the order of the two fallbacks?
Flash, TFTP then ROM
Which of the following is considered a typical default configuration register?
0x2102
Which three components are located in ROM? (Choose 3.)
A. bootstrap
B. POST
C. startup-config
D. IOS file
E. ROMmon
F. running-config
bootstrap
POST
ROMmon
