CCNP Route Ch 1

Question 1

Which two major areas can be used when discussing the high-level overview of a typical enterprise network? Choose two.

Campus backbone

Building distribution

Building access

Enterprise campus

Enterprise edge

Answer 1

Enterprise campus

Enterprise edge

Question 2

Which of the following is used when choosing a dynamic routing protocol? Choose two.

Cost of equipment

Knowledge level of a specific routing protocol

Scalability

Type of links supported

Answer 2

Knowledge level of a specific routing protocol

Scalability

Question 3

BGP is which type of protocol?

Distance vector

Advanced distance vector

Link-state

Path vector

Answer 3

Path vector

Question 4

Which two factors can influence convergence time for a routing protocol? Choose two.

Fine tuning routing protocol timers

Number of end devices with IP addresses.

Configuring route summarization

Implementing authentication

Answer 4

Fine tuning routing protocol timers

Configuring route summarization

Question 5

Scalability of a network includes which two factors? Choose two.

Number of adjacent neighbors

Number of routers

Distance between routers

Ability to do auto summarization

Answer 5

Number of adjacent neighbors

Number of routers

Question 6

Which of the following traffic types is not supported by IPv6?

Unicast

Multicast

Anycast

Broadcast

Answer 6

Broadcast

Question 7

What is the IPv6 multicast address used by EIGRP?

FF02::5

FF02::6

FF02::9

FF02::A

Answer 7

FF02::A

Question 8

Which type of IPv6 address is used by routing protocols for communications only on the link?

Unique local

Site local

Link-local

Multicast

Answer 8

Link-local

Question 9

Which type of ICMPv6 message is sent by a device to request information about the network such as the prefix, prefix length and default gateway?

Neighbor Advertisement

Neighbor Solicitation

Router Advertisement

Router Solicitation

Answer 9

Router Solicitation

Question 10

Which type of ICMPv6 message is sent by a device to inform another device of its IPv6 address and associated Ethernet address?

Neighbor Advertisement

Neighbor Solicitation

Router Advertisement

Router Solicitation

Answer 10

Neighbor Advertisement

Question 11

Which type of network allows access to multiple devices on the same network but does not provide broadcast capabilities?

Point-to-point

Broadcast

NBMA

Multi-access

Answer 11

NBMA

Question 12

Which type of subinterface provides connections similar to physical point-to-point links and has no neighbor discovery issues?

Point-to-point

Point-to-multipoint

Multipoint

All of the above

Answer 12

Point-to-point

Question 13

Which tunneling protocol was developed by Cisco to encapsulate a Layer 3 protocol inside a point-to-point, tunnel-over-IP network?

GRE

DMVPN

IPsec

MPLS

Answer 13

GRE

Question 14

A Layer 3 MPLS VPN over GRE is an example of what type of VPN?

DMVPN

Multi-VPN

Combination VPN

Hybrid VPN

Answer 14

Hybrid VPN

Question 15

What protocol is used by routers implementing DMVPN to determine the next-hop IP address in tunneling networks?

Dynamic GRE

NHRP

mGRE

MPLS

Answer 15

NHRP

Question 16

What framework of open standards that provides confidentiality, data integrity, authentication and anti-replay protection?

IPsec

VPN

PAP

PSK

Answer 16

IPsec

Question 17

R1 has an adjacent RIPng neighbor R2. R1 has a LAN with no neighbors, 2001:DB8:ACAD:1::/64. R1 advertises this prefix to adjacent RIPng neighbor, R2. What metric does R2 display for 2001:DB8:ACAD:1::/64?

1 hop

2 hops

3 hops

4 hops

Answer 17

2 hops

Question 18

How is an interface enabled for RIPng?

Using the network prefix/prefix-length router mode command

Using the ipv6 rip name enable interface command

Interfaces are automatically enabled for RIPng when the RIPng process is started

Using the router ripng name interface command

Answer 18

Using the ipv6 rip name enable interface command

Question 19

Router R1 has multiple routes in its routing table including RIPng routes, directly connected networks and a static default route. R2 receives a default route from R1 but no other routes. This is because R1 uses which option at the end of ipv6 rip name default-information interface command?

static

originate

default-only

only

Answer 19

only