C - 3 (answers)

Question 1

A blade that has teeth that are ground at right angles to the edge is a ____

Answer 1

Ripsaw blade

Question 2

If a small piece of cutoff is close to the blade of a table saw ______

Answer 2

use a push stick to get it away from the blade

Question 3

If a table saw coasts for only a short time after it is turned off, the problem could be that the

Answer 3

Belts are too tight

Question 4

If a table saw is to rip properly, the fence must be exactly

Answer 4

Parallel to the side of the blade

Question 5

In a stacked dado, the swaged teeth of the chippers should be placed at the ______ of the outside blades.

Answer 5

Gullets

Question 6

If the feed of the stock is too slow _____

Answer 6

The blade may overheat

Question 7

Loose knots or split lumber should not be cut on a table saw because they can

Answer 7

Kick back towards the operator

Question 8

Making a 20 mm x 20 mm rabbet cut on a table saw with a single saw blade requires no less than

Answer 8

2 cuts

Question 9

On a table saw, the round knobs found at the centre of the tilt- and height-adjusting handwheels are used to

Answer 9

Lock the handwheels

Question 10

One place you should NOT stand when you use a table saw is

Answer 10

In line with the blade

Question 11

On a table saw, to set the positive stops on the mitre gauge to 45 degrees, you should use a

Answer 11

Framing square

Question 12

Saw arbor nuts are loosened

Answer 12

With the rotation of the blade

Question 13

The adjustable dado head can be adjusted

Answer 13

By rotating the dial

Question 14

The attachment used with a table saw that slides in grooves in the table surface is a

Answer 14

Mitre gauge

Question 15

The blade that eliminates the need to change blades when ripping and crosscutting is a(n) _____

Answer 15

Combination blade

Question 16

The size of a drill press is noted by

Answer 16

Twice the distance from the chuck to the column

Question 17

The jointer is used to ______ boards

Answer 17

Straighten, smooth, square up

Question 18

The more teeth a circular saw blade has

Answer 18

The smoother the cut

Question 19

The table top on a table saw has two machined grooves which are used to

Answer 19

Guide the mitre gauge

Question 20

The aid designed to hold a piece of stock safely while it is being cut with a table saw is

Answer 20

A mitre gauge, push stick, feather board

Question 21

To check if the tilt of the table saw’s blade is at 45 degrees to the table, the most accurate way is to

Answer 21

Two edge mitres and check for 90 degrees

Question 22

To lubricate the screw threads on the tilt-and height-adjusting handwheels, you should use

Answer 22

Graphite or silicone

Question 23

To rip at angles between 45 and 90 degrees on a table saw, you must adjust the

Answer 23

Tilt hand wheel

Question 24

Using a mitre gauge and the rip fence on opposite sides of the blade is _____

Answer 24

Dangerous and should never be attempted

Question 25

What are the two most commonly used materials used for grinding stones on bench grinders?

Answer 25

Silicone carbide and aluminum oxide

Question 26

What is the maximum space allowed between the tool rest and the wheel?

Answer 26

1/8

Question 27

What is an important consideration when using a thickness planer

Answer 27

narrow boards can not be taller than their width and single boards need to be longer than the distance from infeed to out feed

Question 28

When cutting with a table saw, if the stock is 6 inches (150 mm) or less, use ____

Answer 28

A push stick

Question 29

When ripping with the table saw, use the ______ to keep the saw kerf from closing

Answer 29

Splitter

Question 30

When you change blades on a table saw, you should

Answer 30

Disconnect the power

Question 31

When you check to see if the saw blade is perpendicular to the table top, you must place the square against the saw blade so that the square

Answer 31

lands between teeth set towards the square

Question 32

When you cut with a table saw, the blade should be about ____ above the material

Answer 32

1/4 inch (6mm)

Question 33

When you rip narrow stock at a bevel on a table saw, the saw blade must be tilted

Answer 33

Away from the fence

Question 34

When you use both the fence and the mitre gauge to crosscut a number of short pieces to the same length using a table saw, you must use a

Answer 34

Stop block as a spacer

Question 35

On a table saw, when you cut a stopped groove using a dado, you will need to use

Answer 35

One stop block