Bolt On Vehicle Body Panels And Components Flashcards
What is a gap?
A Gap is the width of the opening between panels.
What does Flushness stands for?
Flushness is the difference in height between two panels.
What is a positive Flushness?
A positive Flushness is the fender sticking out from the door!
What is negative Flushness?
The negative Flushness would mean that the gender is inward from the door.
What should you do it there is no vehicle maker recommendation for panel gaps or Flushness?
You should compare the panels to the opposite side of the vehicle!
What happens if they structure is not dimensionally correct?
“Dimensionally”means the correct size and shape
It will be difficult or impossible to achieve correct panel alignment.
What happens if a panel is misaligned to the body
It may give the panel to body a stranger appearance.
Alex and everyone else, after using the Oxy-Acetylene and Mig welders you must turn off the hand pieces and put the Oxy-Acetylene welder away straight away. And/or turn off the Mig welder and put it away straight away. is this true or false?
False my dudes.
Alright my dudes, both technicians say that at the end of a job liquids must be kept in a BUNDED AREA. True or false?
True as the colour blue.
With the Oxy-Acetylene you must make sure to purge the lines of all gases after you have turned off the isolation valves turned off?
TRUE!!! 🤭
At completion of a job you need to make sure that any reusable rags are thrown out as they are not needed.
False. They are still needed because they can be used for other jobs. 😉
When starting a new job all checklist sheets (e.g job cards, reports, hoist logbooks) must be filled out after the job to ensure maximum speed throughout the job.
False. It’s false because you need to do that at the start of the job before the repair. 🤔
Before commencing any work on a vehicle should the OEM repair procedures be sourced and studied first?
YES!
What fire extinguisher would be used on a fire to limit the amount of damage to electrical component in a vehicle?
The CO2 fire extinguisher.
How is correct?
Technician 1 says that before commencing any work on a vehicle safety glasses, safety boots, overalls and protective gloves must be worn.
Technican 2 says that when repairing or inspecting vehclea ensure that the vehicle is properly secured, by either putting transmission in park, applyimg parking brake or wheels chocked securely.
Both Technicians 1 and 2
Before using any power tools what should you do
Check that the tool has been inspected and the tag is in date.
If not take out of action and the supervisor notified.
Why should you read the job sheet before commencing any work?
To see what needs to be repaired or replaced and any time restraints.
How do you move the frunt of the fender?
Loosen the front fasteners adgust and tighten.
How do you move the tear of the fender?
Loosen the rear fasteners ajust and tighten.
Once a tube of adhesive has expired you will need to discharge the tube on a piece of waste paper and left to cure and then can be tossed out.
True. So very true. If left in the tube and then thrown away it will cause rubbish.
Once you have filled a panel with plastic filler, the safety precautions you must take are; use dust extraction equipment, safety glasses and finally to hold your breathe while sanding it back. True or false?
False. It was close to all true but the last safety precaution is incorrect as you wear a mask or respirator.
Besides having a vacuum sanding tool to remove the dust, we can make sure to be sanding in a well ventilated area. True or false?
True.
Disconnection of the battery does always eliminate the risk of un-deployed airbags
True or false
False
When using chemical you don’t need to read the information on the material safety data sheet
True or false
False
What is a Collapse Zone?
Collapse zones are made to compress under impact to prevent fever damage to the vical.
