AREA 1 Flashcards by Ericson Rivera

The distance from the center of the crankshaft to the center of the crankpin.

crank throw
cam shaft
crank rod
crank stroke

crank throw

How well did you know this?

Not at all

Perfectly

Continuous running tests of a single cylinder engine is done in_____ hours.
24 hours
8 hours
6 hours
5 hours

5 hrs

How well did you know this?

Not at all

Perfectly

The winding that is not connected to the power source, but carries current that comes from the magnetic linkage.

secondary windings
stator windings
rotor windings
primary windings

secondary windings

How well did you know this?

Not at all

Perfectly

Engines are not normally used for
4-wheel tractors
4-row harvesters
power sprayers
1-ton rice mills

1-ton rice mills

How well did you know this?

Not at all

Perfectly

If an electric motor rated at 220 volts and 4.8 amperes is converted to 110 volts, then its rated current will be:
2.4 A
7.2 A
4.8 A
9.6 A

9.6A

How well did you know this?

Not at all

Perfectly

Maximum allowed untilled or percent overlap of hand tractors for field operation:
5%
15%
10%
20%

15%

How well did you know this?

Not at all

Perfectly

They are endless belts made with single ply high tensile cords and they are oil and heat resistant.
leather belts
synthetic belts
rubber belts
nylon cords

nylon cords

How well did you know this?

Not at all

Perfectly

Four-wheel tractors are characterized as:
low speed-low torque
low speed-high torque
high speed-high torque
high speed-low torque

low speed-high torque

How well did you know this?

Not at all

Perfectly

The field area (m2) required for testing the performance of a hand tractor is:
200
400
500
300

500

How well did you know this?

Not at all

Perfectly

Trading entity authorized by foreign and local suppliers and/or manufacturers to distribute agricultural machinery to dealers:
manufacturer
distributor
dealer
entrepreneur

distributor

How well did you know this?

Not at all

Perfectly

It is a special arrangement of gears so constructed and located in the transmission system of a 4-wheel tractor that permits one driving wheel to rotate slower or faster than the other and at the same time propel its share of the load.
Gear box
Clutch
Differential
Power take-off

Differential

How well did you know this?

Not at all

Perfectly

A gear whose teeth are straight, but the sides are tapered so that they would intersect the axis at a common point.
miter gear
spur gear
straight bevel gear
helical gear

straight bevel gear

How well did you know this?

Not at all

Perfectly

The perpendicular distance between the wing and the point of the share determines the:

traverse dimension of plow
longitudinal dimension of plow
diagonal dimension of plow
maximum dimension of plow

traverse dimension of plow

How well did you know this?

Not at all

Perfectly

It produces its torque by virtue of the force of weights pressing against the driving or frictionally driven member.

plate clutch
disc clutch
conical clutch
centrifugal clutch

centrifugal clutch

How well did you know this?

Not at all

Perfectly

Sprayers are used primarily for the application of:

herbicides
fungicides
insecticides
pesticides

pesticides

How well did you know this?

Not at all

Perfectly

It is a method of pump drive where the pump is built with a common shaft and bearings for the pump and the driver forming a single compact unit:
closed- connected
belt-driven
direct-coupled
sprocket-driven

closed- connected

How well did you know this?

Not at all

Perfectly

This is the application and management of pests by manipulating the environment or implementing preventive practices such as using plants that are resistant to pests, proper timing of planting and crop rotation.
Ecological Control
Cultural Control
Biological Control
Chemical Control

Cultural Control

How well did you know this?

Not at all

Perfectly

Which of the following is not a typical example of a small single-cylinder engine?
air-cooled gasoline engine
air-cooled diesel engine
water-cooled gasoline engine
water-cooled diesel engine

water-cooled gasoline engine

How well did you know this?

Not at all

Perfectly

This type of transmission system is common to two wheel tractors

Direct coupling
Chain and sprockets
Gear systems
Differential

Chain and sprockets

How well did you know this?

Not at all

Perfectly

Planters which are designed to plant one or more seeds or plants with row spacing equal to hill spacing:

solid planters
precision planter
check row planter
hill drop planter

check row planter

How well did you know this?

Not at all

Perfectly

How many spark plugs are needed in a 16-valve, 4-stroke, 4-cylinder compression ignition engine?

0
4
8
6

How well did you know this?

Not at all

Perfectly

The process of allowing into the engine chamber a volume of air larger than what the engine chamber would normally admit during suction stroke.
Turbocharging
Supercharging
Choking
Intake

Supercharging

How well did you know this?

Not at all

Perfectly

For complete combustion of diesel, how much air is needed?
11.1 kg/kg of diesel
12.5 kg/kg of diesel
14.9 kg/kg of diesel
24.5 kg/kg of diesel

14.9 kg/kg of diesel

How well did you know this?

Not at all

Perfectly

It absorbs the pressure of the expanding gases.

Piston rings
Connecting rod
Crankshaft
Piston

Piston

How well did you know this?

Not at all

Perfectly

It is a measure of the tendency of gasoline to resist detonation during combustion in an engine Anti-knock Fire point Cetane number Octane number

Octane number

How much carbon dioxide is produced for every kilogram of diesel fuel burned? 0.65 kg/kg of fuel 16 kg/kg of fuel 24.5 kg/kg of fuel 3.11 kg/kg of fuel

3.11 kg/kg of fuel

Which gas constitutes the highest percentage in the composition of exhaust gases when ethanol was used as fuel in an SI engine? Carbon dioxide Nitrogen Oxygen Carbon monoxide

Nitrogen

In engines with overhead valves, which pushes the pushrods? Tappet Rocker arm Cam Crankshaft

Tappet

This refers to the changes in the front and rear wheel reaction that occur when a tractor pulls a drawbar load. Resistance Traction Rolling moment Weight transfer

Weight transfer

How many liters of alcohol would be required to produce the same heat value as a liter of gasoline? 1 L 1.6 L 2 L 3.2 L

1.6 L

What type of utility change happens if I make the product available where it is most needed Form Time Place Possession

Place

Which subsystem is in charge of wholesalers, retailers, traders, middleman, etc Input Processing Production Marketing

Marketing

What is not a characteristic of an agricultural product SEASONAL fresh perishable variable

fresh

hat is not a characteristic of a wholesaler Substantial working capital Has transportation ability Carries assortment of different products in small quantities Access to market facilities

Carries assortment of different products in small quantities

A Classification of an agribusiness product that is directly consumed by buyers Fresh Semi Processed Finished Point of Consumption

Finished

What hinders farmers from directly transacting with supermarkets and hypermarkets? Creating a marketing association Having a consolidator Lacks transaction document Has a consolidator

Lacks transaction document

The following are Product Strategies except Branding Strategy Packaging Strategy Labeling Strategy Pricing Strategy

Pricing Strategy

This is where marketing ends Point of consumption Point of production At the farmer’s home Usually the first sale of the farmer

Point of consumption

This is the start of the agribusiness marketing chain Input Subsystem Production Subsystem Processing Subsystem Marketing Subsytem

Input Subsystem

Which is not currently a trend in marketing Increase in supermarket Increase in food safety Change in preferences in terms of consumption Use of cash instead of digital currency

Use of cash instead of digital currency

Type of utility that happens when a middleman freezes pork product to make it available when most needed Form Time Place Possession

Time

It is the process of continuously and profitably satisfying customer’s needs, wants and expectation superior to competition Input Subsystem Production Subsystem Processing Subsystem Marketing

Marketing

The 4 Ps of marketing are Product, Price, Place, Promotion Product Price Packaging, Promotion Packaging, Price, Place, Promotion Packaging, Product, Price, Promotion

Product, Price, Place, Promotion

When I deliver earlier than expected, I provide Happiness Satisfaction Dissatisfaction Delight

Delight

The type of orientation that focuses on the needs of the customer Product concept Selling concept Production concept Marketing concept

Marketing concept

This occurs when total revenue equals total costs. breakeven point Interest maximum profit maximum total revenue

breakeven point

In deciding whether one should replace an old machine with a new one, the purchase cost of the old machine is treated as a/an book cost burden cost opportunity cost sunk cost

sunk cost

Among the following, that which can be classified as overhead cost is Cost of plastic cups in a coffee shop Cost of power used to run plant equipment Cost of computer parts in a store that assembles and sells computer units Wages of an injection machine operator in a plastics factory

Cost of power used to run plant equipment

PAES 303:2000 provides the power rating of roller chain based on a service life of _______? 15 000 hr 1 000 hr 5 000 hr 10 000 hr

15 000 hr

These are multiple keys in the general form of internal and external gear teeth, used to prevent relative rotation of cylindrically fitted machine parts. Rigid couplings Involute splines Square splines Friction clutches

Involute splines

What is the degree of freedom of a spherical joint? 11 2 3 -1

A board principally made from wood chips and formed by hot press process with adhesive: plywood fiberboard adhesive-bonded fiberboard particle board

particle board

These are activities which create faster and more efficient performance of other marketing activities. These include market intelligence and marketing information dissemination, financing, provision of marketing support facilities, and promotions. Transactional activities Physical handling and distribution of products Facilitating activities Agroservices activities

Facilitating activities

This is a continuous function of marketing. The objective of this function is to inform prospective buyers of product availability and also to increase sales. Pricing Promotion Research and development Distribution

Promotion

Because of the variability in agricultural outputs, ________ must be done to facilitate buying, selling, transportation, storage, and pricing of the produce. __________ is done to standardize measurements, which could be in terms of size, weight, and overall quality. Grading Assembly Negotiation Packing/packaging

Grading

These are the types of middlemen who do the business of negotiating in behalf of the producers and the buyers. They do not assume ownership of the products that they are handling. Retailers Wholesalers Assemblers Agents and brokers

Agents and brokers

Marketing overcomes several separations. One of these is separation in __________. This happens when producers tend to locate where it is economical to produce while consumers are located in many scattered locations. Separation in Time Separation in Information Separation in Location Separation in Value

Separation in Location

In a vegetable farm, cost of planting materials and fertilizers, and wages of farmers are examples of book costs disposal costs operation and maintenance costs overhead expenses

operation and maintenance costs

In a cassava processing plant, costs of land, building and milling machines are examples of investment cost operation and maintenance costs overhead expenses recurring costs

investment cost

The following are characteristics of an ordinary annuity except Compound interest is paid on all amounts in the annuity. The amounts of periodic payments are equal. The payments are made at the beginning of each period. The payments are made at equal interval of time.

The payments are made at the beginning of each period

This is a method of computing for depreciation charges wherein the annual charge is a fixed percentage of the book value at the beginning of the year to which the depreciation applies. Declining balance method Sinking fund method Straight line method Sum-of-years digit method

Declining balance method

The time rate of doing work or delivering energy, expressed as the amount of work done W or transferred energy divided by the time elapsed t or computed as W/t. A. Force B. Power C. Work D. Energy

What is the battery nominal voltage of a 4-wheel 90-hp tractor? A. 12 Vac B. 24 Vdc C. 9 Vdc D. 12 Vdc

The battery of a 24-volt combine harvester needs to be replaced. Two 12-volt batteries are to be used as its replacement. What should be the connection of the batteries? A. Series B. Parallel C. Series-Parallel D. Any connection

A. Series

The 12-volt battery of a boom sprayer was drained. A 12-volt battery attached to a vehicle can be used for starting the engine. Jumper wires are available. What should be the connection of the two batteries to facilitate starting? A. Series B. Parallel C. Series-Parallel D. Any connection

B. Parallel

A tractor cannot start due to defective battery. It is being pushed by workers while lever is set to first gear. What should be foot-pressed and released abruptly to start engine? A. Brake B. Clutch C. Clutch and Brake D. Accelerator

B. Clutch

To gradually move a tractor from stop, what should be released while pressing the accelerator? A. Brake B. Clutch C. Clutch and Brake D. Lever

B. Clutch

To roll the tractor set at first gear in a flat land, what should be foot-pressed? A. Brake B. Clutch C. Clutch and Brake D. Accelerator

D. Accelerator

To slow down the tractor running at first gear in a flat land, what should be foot-pressed? A. Brake B. Clutch C. Clutch and Brake D. Accelerator

B. Clutch

To gradually stop a fast running tractor, what should be foot-pressed? A. Brake B. Clutch C. Clutch and Brake D. Accelerator

C. Clutch and Brake

What is the safest gear setting for a descending tractor in a 10% slope? A. Neutral B. Third gear C. Second gear D. First geaR

In a routinary check before using the tractor, what should be checked first? A. Fuel B. Water C. Brake D. Oil

To roll a tractor from stop and neutral position with engine off in a sloping land, what should be foot-pressed? A. Brake B. Clutch C. Clutch and Brake D. Lever

The connection to the tractor of an erratic battery is to be stopped quickly. What battery terminal should be disconnected first? A. Positive B. Negative C. Both terminals D. Any terminal

A new battery is to be installed to a tractor. What battery terminal should be connected first? A. Positive B. Negative C. Both terminals D. Any terminal

The battery drains while tractor is not in use. What battery terminal should be disconnected when tractor is not in use? A. Positive B. Negative C. Both terminals D. Any terminal

What kind of hitch is best for a non-hydraulic disk plow? A. 1-point hitch B. 2-point hitch C. 3-point hitch D. 4-point hitch

What kind of hitch is best for a tractor trailer? A. 1-point hitch B. 2-point hitch C. 3-point hitch D. 4-point hitch

A 24-volt battery of a pineapple harvesting conveyor needs to be charged on field using 12-volt solar modules. What is the minimum number of solar modules required? A. One B. Two C. Three D. Four

A 12-volt battery of a boom sprayer needs to be charged on field using 6-volt solar modules with 2 modules in parallel to speed up charging. How many solar modules are required? A. Two B. Four C. Six D. Eight

In an aerogenerator exceeding 100 kw capacity, which part is responsible in converting rotational movement to electricity? A. Rotor B. Turbine C. Alternator D. Governor

What component of force is used in multi-bladed windmills? A. Lift force B. Drag force C. Side force D. Drop force

What component of force is used in savonius windmills? A. Lift force B. Drag force C. Side force D. Drop force

The type of pump is appropriate for multi-bladed windmills. A. Hydraulic B. Pneumatic C. Reciprocating D. Diaphragm

While the windmill is in operation, what efficiency can exceed 100%? A. Volumetric B. Transmission C. Rotor D. All of the above

What wind energy resource is located about 10-16 km from Earth surface with velocity over 150 kph? A. Terrestrial wind B. Extra-terrestrial wind C. Jet stream D. High wind

In multi-bladed windpumps, which part is responsible in converting rotational movement to reciprocating action? A. Rotor B. Connecting rod C. Reciprocating pump D. Crank arm

What tail type of multi-bladed windpump is more effective for windy areas? A. Hinged side vane B. Ecliptic C. Manual folding D. No tail

In wind farm development, which should be done first? A. Rotor B. Energy demand survey C. Transmission D. Wind velocity measurement

In multi-bladed windpump manufacturing, which should be done first? A. Rotor blade B. Rotor frame C. Tower D. Jig

A. Rotor blade B. Rotor frame C. Tower D. Jig

In windmill design, what should be the average rotor blade twist angle in degrees to have a tip speed ratio of 1:1? A. 30 B. 45 C. 60 D. 75

If typical overall efficiency of savonius windmills is 7-10%, what is the typical overall efficiency of aerogenerators? A. 7-10% B. 15-17% C. 18-21% D. 90-95%

Which battery is designed for slow charging and slow discharging? A. Maintenance-free battery B. Automotive battery C. Solar battery D. All of the above

Kind of battery useful in solar-powered energy systems. A. Lead-acid battery B. Automotive battery C. Solar battery D. All of the above

Material used in solar cells. A. Silicon B. Boron C. Equal silicon and boron D. Silicon with little boron

In a sunny 12:00 noon in the Philippines, what is the likely voltage reading of solar pump without battery when load is in turned on? A. 20-22 V B. 16-19 V C. 14-15 V D. 11-13 V

In a sunny 12:00 noon in the Philippines, what is the likely voltage reading of solar battery charger when no battery is being charged? A. 20-22 V B. 16-19 V C. 14-15 V D. 11-13 V

At 8:00 P.M. in the Philippines, what is the likely voltage reading of a solar home system when all loads are turned on? A. 20-22 V B. 16-19 V C. 14-15 V D. 11-13 V

In solar panel installation, which positive polarity wire should be connected last to the battery control unit? A. Solar module B. Load C. Battery D. Monitor

If a coconut tree shades half of solar module, which condition is true? A. Zero voltage B. Low voltage C. Zero amperage D. Low amperage

A 260 kw hydro power plant is classified as A. Microhydro B. Minihydro C. Small hydro D. Big hydro

Under Philippine classification, what is the maximum power rating for microhydro? A. 25 kw B. 50 kw C. 75 kw D. 100 kw

Refers to machines collectively. A. Equipment B. Tools C. Machinery D. Machineries

The process of dealing with or controlling things. A. Management B. Managing C. Supervising D. Administering

The action of promoting and selling products or services, including market research and advertising. A. Certifying B. Marketing C. Endorsing D. Recommending

. Which one is a part of a vertical feed mixer? A. Screw B. Hopper C. Discharge chute D. All of the above

A feed mixer tested to have mixing coefficient of variation of 10-15% is rated as A. Poor B. Fair C. Good D. Very good

As a standard, stripping efficiency of the mechanized stripping machine shall be at least A. 70% B. 80% C. 85% D. 90%

A 6-bladed windmill with 8 meters rotor diameter and 45 degrees twist angle is to be modified due to insufficient starting torque. What should be done? A. Increase blades B. Decrease blades C. Increase twist angle D. Decrease twist angle

Answer: A (since increasing blades increases torque)

A windmill with 6 meters rotor diameter, 5 cm pump diameter and 2 cm crank arm is to be modified due to low volumetric efficiency. What should be done? A. Enlarge rotor B. Reduce rotor C. Elongate crank arm D. Enlarge pump diameter

Answer: C (since elongating crank arm increases pump stroke and volumetric efficiency)

A 3-bladed 40-meter tall aerogenerator with 20 meters rotor radius designed for 6 m/s wind can’t rotate. Average windspeed at rotor center is 5.5 m/s. Which part needs to be increased? A. Number of blades B. Rotor radius C. Crank arm D. Tower height

D (windspeed is higher at higher elevation; increasing rotor radius will severely affect twist angle of entire blade & tip-speed ratio; aerogenerators have no crank arm)

The benefits to society regardless of who in the society receives the benefits. A. Financial benefit B. Economic benefit C. Revenue D. Sales

Benefits less costs excluding depreciation. A. Profit B. Net benefit C. Cash flow D. Economic benefits

. Which one is a one-time expense? A. Investment B. Single cost C. One-time cost D. Operating cost

Annually recurring cost. A. Investment B. Operating cost C. Contingency D. Operating capital

Land is an example of A. Investment B. Operating cost C. Contingency D. Operating capital

Manager’s salary is an example of A. Investment B. Operating cost C. Maintenance cost D. Operating capital

7. The cash component of investment. A. Cash investment B. Operating cost C. Contingency D. Operating capital

Contingency is normally what percentage of investment cost? A. 5% B. 10% C. 15% D. 20%

What is market price deducted by tax. A. Discounted price B. Taxed price C. Shadow price D. Economic price

The equivalent value of a property at any given year. A. Salvage value B. Economic value C. Book value D. End value

What feasibility indicator is best for determining how fast the project recovers the investment? A. NPV B. IRR C. BCR D. Payback period

What feasibility indicator is best for determining how much can you gain from a certain project? A. NPV B. IRR C. BCR D. Payback period

What feasibility indicator is normally compared to bank’s interest rate? A. NPV B. IRR C. BCR D. Payback period

Which among the feasibility indicators is best for determining project performance? A. NPV B. IRR C. BCR D. Payback period

What analysis is done to determine the degree of project feasibility at various scenarios? A. Financial analysis B. Economic analysis C. Risk analysis D. Sensitivity analysis

What feasibility analysis uses shadow prices? A. Financial analysis B. Economic analysis C. Risk analysis D. Sensitivity analysis

What feasibility analysis uses market prices? A. Financial analysis B. Economic analysis C. Risk analysis D. Sensitivity analysis

Which situation is better and attainable for a good economy? A. High discount rate B. Low discount rate C. Fast discount rate D. No discount rate

The normal combined discount and inflation rate of the Philippines. A. 2-4% B. 5-7% C. 8-12% D. 16-20%

The discounted cash flow at project start is always equal to ____. A. Zero B. Net benefit C. Net profit D. Net cash flow

. The price at which there is no loss or gain. A. Discounted price B. Optimum price C. Minimum price D. Break-even price

The discount rate when the Net Present Value is zero. A. Break-even rate B. IRR C. BCR D. ROI

What is the effect of increasing inflation rate to discounted cash flow at project start? A. Increases B. Decreases C. Fluctuates D. None

What is the effect of increasing discount rate to discounted cash flow at year 10 of the project? A. Increases B. Decreases C. Fluctuates D. None

Which one is true when discount rate increases? A. NPV increases B. NPV decreases C. Risk decreases D. Capital reduces

At project start, the net cash flow of the cassava processing venture is -7 million pesos due to loan and revenue is not materialized yet. Discount rate is 10%. What is the value of the discounted cash flow in million pesos at project start? A. 7 B. -7 C. -7.07 D. -7.7

B(At project start or time=0, the discounted cash flow is also equal to the net cash flow)

Using financial feasibility analysis, the Net Present Values (NPVs) of farm-to-market road, irrigation and flood control projects are 22.5, 7.5 and -3.1 million pesos, while the Internal Rate of Returns (IRRs) are 15%, 7% and 2.1%, respectively. Annual discount plus inflation rate is 10%. Which project shall be implemented? A. Farm-to-market road B. Irrigation C. Flood control D. None

Answer: A (since only Farm-to-Market road project has IRR higher than discount plus inflation rate)

Using economic feasibility analysis, the Net Present Values (NPVs) of small water impounding project (SWIP), shallow tubewell, small scale irrigation project (SSIP) are -0.5, -0.9 and 0 million pesos, respectively. The proposed projects are owned by the government. Which project is economically feasible? A. None B. SWIP C. Shallow tube well D. SSIP

Answer: D (In econ. analysis, NPVof 0 is feasible since it has economic benefits even if it is just break-even)

Microhydro, solar electrification and covered lagoon biodigester projects are evaluated for financial feasibility. Each requires PHP 20,000,000 investment. Only one project can be funded. The financial internal rates of return are 15%, 9% and 8%, respectively. Annual discount plus inflation rate is 10%. Which project shall be implemented? A. Covered lagoon biodigester B. Microhydro C. Solar electrification D. None

Answer: B (since its IRR is higher than discount plus inflation rate)

A banana production and export project is being evaluated for financial feasibility. At 12% annual discount rate, it has the following feasibility indicators: net present value of 1.8 billion pesos and internal rate of return of 58%. If annual discount rate drops to 9%, will it be feasible? A. No B. Yes C. Maybe D. Insufficient data to determine

Answer: B (if it is feasible at 12% discount rate, the more it will be feasible at 9%)

In what year was the Implementing Rules and Regulations (IRR) of the Philippine Agricultural and Biosystems Engineering Act of 2016 approved? A. 2016 B. 2018 C. 2020 D. 2022

What law is known as the Philippine Agricultural and Biosystems Engineering Act of 2016? A. RA 9513 B. RA 10601 C. RA 10915 D. RA 9736

Agricultural and Biosystems Engineering refers to the application of ________ and designs to the processes and systems involved in the sustainable production, post production and processing of safe food, feed, fiber, timber and other agricultural and biological materials and the efficient utilization, conservation, and management of natural and renewable resources in order to enhance human health in harmony with the environment. A. Agriculture B. Engineering C. Science D. Engineering science

In ABE law, agricultural and biosystems consist of crops, forestry and other plants, poultry, livestock, fisheries and _____ resources and other animals, wildlife and other living things. A. Agriculture B. Aquaculture C. Farm D. Land

Agricultural and Biosystems Automation and Instrumentation refers to the use and application of agricultural and biosystems ________. A. Circuits B. Instruments C. Sensors D. Integrated circuits

Agricultural and Biosystems Resource Conservation and Management refers to measures of conservation and proper management of agricultural and _______ resources. A. Biological B. Zoological C. Farm D. Water

In RA 10915, agricultural and _________ refers to local activity or series of activities to maintain or raise the quality or change the form or characteristics of agricultural, fishery, forestry and biological products/materials. A. Quality control B. Forestry C. Bio-processing D. Fishery

Agricultural and _______ System refers to utilization of information systems, database, and other information management tools for agricultural use, biological systems modeling to understand the mutual response between life and the environment. A. Computer B. Geographic Information C. Modeling D. Bio-information

Agricultural and Biosystems Power and Machinery refers to farm power and machinery for the production, harvesting, processing, storage, manufacture, preserving, transporting and _____ of agricultural and biological products/materials. A. Distribution B. Quality control C. Marketing D. Sales

Agricultural and Biosystems Buildings and Structures refer to buildings and structures for the production, harvesting, processing, storage, ______, preserving, transporting and distribution of agricultural and biological products/materials. A. Treatment B. Manufacture C. Quality control D. Sales

The ____ earned by the professional shall be required in the renewal of professional license. A. Degree B. BSAE degree C. BSABE degree D. CPD credit units

Any person who violates any of the provisions of RA 10915, upon conviction, shall be penalized by a fine of not less than P100,000 but not more than ___, or imprisonment of not less than 6 months but not more than 5 years, or both fine and imprisonment, at the court discretion. A. P200,000 B. P300,000 C. P400,000 D. P500,000

In Section 17 of RA 10915, which one is not a scope of Land and Water Resources Engineering? A. Irrigation B. Soil and water C. Aquaculture D. Meteorology

Which republic act is known as the Philippine Agri-Fishery Mechanization Law? A. RA 9513 B. RA 10915 C. RA 10601 D. RA 9736

. Under RA 10915, which one is not under the scope of Land and Water Resources Engineering? A. Irrigation B. Soil and water C. Aquaculture D. Meteorology

Under Washington Accord, an Agricultural and Biosystems Engineer who passed licensure examination in the Philippines can practice his/her profession in another Washington Accord member country. A. Yes B. No C. Indeterminate D. Insufficient data to determine

In Washington Accord, the contract of ABE services signed in the Philippines is valid in another Washington Accord member country. A. Yes B. No C. Indeterminate D. Insufficient data to determine

As provided in Article VI Section 27 of AFMech Law, the ___________ is designated as the premier and reference testing center in the country for agricultural and fisheries machinery. ________. A. BAFE B. AMTEC C. IPO Philippines D. BAFS