Apparatus, Tools, and Appliances Flashcards

1
Q

All reports of incidents in which Apparatus / Vehicles are involved including:

A

Failure to start
Loss or Breakage of Part
Accident
Court hearing
Investigation

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What information are included in a incident report

A

Serial Number of Apparatus
Name of Driver
Mileage

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

What are the 4 types of alpha-numeric tracking numbers to track and classify incidence and accident reports

A

Accident Chargeable – AC
Accident Non-Chargeable – ANC
Incident Chargeable – IC
Incident Non-Chargeable – INC

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

The Boards findings will be referred to DFC Risk Management within ____ calendar days of
accident

A

14

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

BFC or other Investigator:
Will make a package of:

A

o Form 7
o Special Reports
o Police Accident Report
o Safety Responsibility Form

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

Safety Officer will notify Apparatus Division of all Accidents & provide the following:

A

Date & Time of Accident
Accident Control Number
Unit involved
Photos
Whether or not Insurance information was provided

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Member will prepare & forward a Special Report with results of hearing within _____ calendar days

A

5

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

How often is the oil checked?

A

Daily

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Notify Apparatus Division is engine hours exceed _____

A

200

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Check transmission fluid temp with the engine operating at _____ rpm

A

1,000

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

How often are stemsco checked?

A

Daily

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What are indicators of a tired lug nut?

A

If temp of wheel nut exceeds 248 degrees because of binding brake or seized bearing
Indicator will blister & become discolored
Place Vehicle OOS & report to Fleet Maintenance

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

When are grease fittings lubricated?

A

Once a month or basis of service performed

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

Units with automatic grease lubrication device will check reservoir ______ as needed

A

daily and as needed

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What equipment are gaskets used in

A

Play pipes
Wagon Pipes
Monitor Nozzles
Ladder Pipes

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

How often should ground ladders be cleaned & lubricated?

A

Every 3 months

17
Q

After cleaning - all metal to metal contact surfaces should be rubbed with ______ _______

A

Paraffin wax

18
Q

Heat Sensor Labels will change color after being exposed to heat greater than _____ degrees

A

300F

19
Q

Heat sensor labels are located inside each beam below _______________

A

2nd rung down from top in middle of section

20
Q

How many heat sensor labels are on a ladder?

A

4

21
Q

Ground Ladders should have ________ non-destructive service testing in accordance with _______ of NFPA ____

A

Annual, Chapter 7, 1932

22
Q

By _____ of each year Company Officers will ensure Snow Chains are properly:

A

7/31, Repaired, Correct Size, Ready for immediate use