ADT 7-2 Flashcards
The spring rate of a spring is measured in units of ________.
Lb. per Inch
Two technicians are discussing torsion bars. Technician A says that many torsion bars are adjustable to allow for ride height adjustment. Technician B says that torsion bars are usually marked left and right and should not be switched side to side. Which technician is correct?
Both Technicians A and B
A vehicle makes a loud noise while traveling over bumpy sections of road. Technician A says that worn or deteriorated control arm bushings could be the cause. Technician B says that worn or deteriorated strut rod bushings could be the cause. Which technician is correct?
Both Technicians A and B
Two technicians are discussing MacPherson struts. Technician A says that in most applications the entire strut assembly rotates when the front wheels are turned. Technician B says a typical MacPherson strut suspension system uses only one control arm and one ball joint per side. Which technician is correct?
Both Technicians A and B
Technician A says that regular replacement shock absorbers will raise the rear of the vehicle that is sagging down. Technician B says that replacement springs will be required to restore the proper ride height. Which technician is correct?
Technician B only
A vehicle used for 24-hour-a-day security was found to have damaged suspension-limiting rubber jounce bumpers. Technician A says sagging springs could be the cause. Technician B says defective or worn shock absorbers could be the cause. Which technician is correct?
Both Technicians A and B
The part of many rear suspension systems that controls side-to-side movement is called the ________.
Track Rod or Panhard Rod
Two technicians are discussing air shocks. Technician A says that air is forced through small holes to dampen the ride. Technician B says that air shocks are conventional hydraulic shock absorbers with an airbag to control vehicle ride height. Which technician is correct?
Technician B only
The owner of a pickup truck wants to cut the coil springs to lower the vehicle. Technician A says that the ride will be harsher than normal if the springs are cut. Technician B says that the springs could be damaged, especially if a cutting torch is used to cut the springs. Which technician is correct?
Both Technicians A and B
A MacPherson strut is a structural part of the vehicle. True or False?
True
Unusual noise during a test drive can be caused by which of the following?
A.) Defective wheel bearings or stabilizer bar links.
B.) Defective or worn control arm bushings or ball joints.
C.) Worn or defective CV joints.
D.) All of the above
D.) All of the above
Two technicians are discussing non-indicator-type ball joint inspection. Technician A says that the vehicle should beon the ground with the ball jointsloaded,then checked for freeplay. Technician B says that the ball joints should beunloadedbefore checking for freeplay. Which technician is correct?
Technician B only
Most manufacturers specify a maximum axial play for ball joints of about ________.
0.050 in. (1.27 mm)
The preferred method to separate tapered chassis parts is to use ________.
A puller tool or two hammers to shock and deform the taper.
A light film of oil is observed on the upper area of a shock absorber. Technician A says that this condition should be considered normal. Technician B says that a rod seal may bleed fluid during cold weather, causing the oil film. Which technician is correct?
Both Technicians A and B
Before the strut insert can be removed from a typical MacPherson strut assembly, which operation is necessary to prevent possible personal injury?
The coil spring should be compressed.
What should the technician do when replacing stabilizer bar links?
The links can be replaced individually, yet the manufacturer often recommends that the links at both ends be replaced together.
A noise and a pull toward one side during braking is a common symptom of a worn or defective ________.
Strut rod bushing
To help prevent vehicle wandering on a vehicle with torsion bars, the ride height (trim height) should be within ________ side to side.
0.125 in. (3.2 mm)
Two technicians are discussing suspension bushings. Technician A says that replacing the control arm bushings usually requires special tools. Technician B says using high-performance urethane bushings may cause excessive noise to be transferred to the passenger compartment. Which technician is correct?
Both Technicians A and B
A vehicle equipped with a coil spring front suspension and a leaf spring rear suspension “dog tracks” while driving on a straight, level road. Technician A says that a broken center bolt could be the cause. Technician B says defective rear shock absorbers could be the cause. Which technician is correct?
Technician A only
When axle windup is controlled by the rear-leaf spring during acceleration, this system is called ________.
Hotchkiss Drive
A loud “bang” is heard and felt every time the accelerator is depressed or released on a rear-wheel-drive vehicle. Technician A says that a leaf spring could be the cause. Technician B says a broken torque arm could be the cause. Which technician is correct?
Both Technicians A and B
Technician A says that all leaf springs are mounted lengthwise on the rear of many vehicles. Technician B says that some vehicles use a transversely mounted leaf spring on the rear. Which technician is correct?
Technician B only