4.3 Electrical Circuits Flashcards
what is Kirchoff’s Second Law?
Kirchoff’s Second Law states that in any closed loop. the sum of the e.m.f is equal to the sum of the products of the current and the resistance
(in other words the total potential difference is equal to the sum of all the potential differences of the components)
∑Ɛ = ∑IR
what is Kirchoff’s First law?
Kirchoff’s First law states the sum of currents entering a junction in a circuit is equal to the sum of the currents leaving the junction
what is Kirchoff’s Second Law a consequence of?
the conservation of energy
what is Kirchoff’s First Law a consequence of?
the conservation of charge
what is the equation for total resistance in a series circuit?
Rtotal = R1 + R2 + R3
opposite to spring constant and capacitors
what is the equation for total resistance in a parallel circuit?
1 / Rtotal = 1 / R1 + 1 / R2 + 1 / R3 opposite to capacitors and spring constants
how are ammeters connected in circuits and what is the resistance of them?
connected in series, designed to be close to zero resistance
how are voltmeters connected in circuits and what is the resistance of them?
connected in parallel, designed to have close to infinite resistance so that none of the current flows through them
what is the rule for current in series circuits?
stays the same
what is the rule for current in parallel circuits?
splits at junctions
what is the rule for voltage in series circuits?
splits, the voltage of the cell is equal to the sum of the voltages across the components (not necessarily and equal split)
what is the rule for voltage in parallel circuits?
the same, each branch has the same voltage as the cell (so would split if there were more than one component on the same branch)
what is internal resistance?
internal resistance of a source of e.m.f is the resistance to electric current of the materials inside, when current flows energy is transferred to these materials resulting in the p.d dropping
what is the difference between the e.m.f and the terminal p.d known as?
the ‘lost volts’
define terminal p.d
the potential difference recorded across the terminals of the cell
what is the equation that links terminal p.d and e.m.f?
Ɛ - Ir = V, can also be written as…
Ɛ = V + Ir
Ɛ = I (R + r)
where Ɛ = electromotive force
Ir = lost volts
V = terminal p.d
uppercase R is used for external quantities (in this case the resistance of the circuit)
lowercase r is used for internal quantities (in this case the internal resistance)
outline an investigation to determine internal resistance of a chemical cell/other source of e.m.f
- set up a circuit with a battery or cell, an ammeter in series, a variable resistor and a voltmeter in parallel
- vary the current by changing the value of the load resistance R using the variable resistor
- measure the voltage for different values of current, record your results in a table and plot a graph of voltage (y axis) against current (x axis)
- remember E = V + Ir, rearranging to get V = -rI + E, means that because its a straight line the y intercept is the EMF and the gradient = -r, multiply gradient by -1 to get r
what is a potential divider circuit?
a potential divider circuit uses two resistors in series to split or divide the voltage of the supply in a chosen ratio so that a chosen voltage can be provided to another device or circuit (see page 194 for good diagrams)
what is the potential divider equation? what are the two versions?
V1 / V2 = R1 / R2
Vout = R2 / R1 + R2
how can you specifically alter the output voltage in a potential divider circuit?
use a variable resistor as the second resistor so you can adjust the resistance ration and therefore the voltage ratio
outline the procedure to investigate potential divider circuits using an NTC thermistor, describe how it works…
-an NTC thermistor has a HIGH resistance at low temperatures, but LOW resistance at high temp
-a thermistor can be used in a potential divider circuit to provide a variable output voltage to control a heater
-when the temp is low and therefore the resistance of the thermistor is high, the thermistor has a high output voltage which is enough to switch the heater on
-when the temp is high the resistance of the thermistor decreases meaning it will have a lower output voltage so the heater switches off
-when actually performing the experiment you must place a thermistor in a water bath with a bunsen burner to change the temp
WORKS LIKE A HEAT SENSOR
(note draw a normal potential divider circuit but with a thermistor at Vout)
outline the procedure to investigate potential divider circuits using an LDR, describe how it works…
- an LDR has HIGH resistance in dark, but LOW resistance in light
- an LDR can be used in a potential divider circuit to provide a variable output voltage to control street lamps
- when the incident light intensity is low (dark conditions) the resistance of the LDR is high, the LDR has a high output voltage which is enough to switch the street lamp on
- when the incident light intensity is high (bright conditions) the resistance of the LDR decreases meaning it will have a lower output voltage so the street lamp switches off
WORKS LIKE A LIGHT SENSOR
(note draw a normal potential divider circuit but with an LDR at Vout)
What is a potentiometer
alternative to using a potential divider.
It’s basically a variable resistor with three terminals and a sliding contact. Adjusting the contact varies the p.d. Between the the two terminals, giving a variable Vout
