19 - TeePeeSee 107 Flashcards
If you need to measure with an accuracy greater than a hundredth of an inch? A) Firm-joint caliper B) Steel rule C) Steel Tape D) Vernier Caliper
D) Vernier caliper
What tool can measure both inside and outside diameter of a pipe? A) Firm Joint Caliper B) Lock Joint caliper C) Slide caliper D) Spring Joint Caliper
C) Slide Caliper
If a micrometer is graduated in inches, how far does the spindle move in one complete revolution? A) 1/25 in B) 1/40 in C) 1/50 in D) 1/60 in
B) 1/40 in
The part of the framing square called the blade is? A) Handle B) Long Arm C) Short Arm D) Same as the tongue
B) Long Arm
Which head is used on a combination square for measuring any size angles? A) Center B) Pivotal C) Protractor D) Square
C) Protractor
Wrench made of ________ steel are light weight? A) Carbon Steel B) Chrome-vanadium steel C) Molybdenum steel D) Stainless steel
B) Chrome-vanadium steel
Distance across flats on a bolt head usually equal diameter times? A) 1/2 B) 1 C) 1 1/2 D) 2
C) 1 1/2
The type of socket handle that provides most leverage for breaking loose very tight nuts or bolts is the? A) Hinged drive lug B) Ratchet socket C) Sliding T-Bar D) Speed
A) Hinged drive lug
Best wrench for removing a frozen nut from a bolt is? A) Adjustable wrench B) Socket wrench C) Striking-face box wrench D) Torque wrench
C) Striking-face box wrench
Whole tip of a _______ screwdriver fits into screwhead there by reducing slippage. A) Flange tip blade B) Off set C) Parallel tip blade D) Phillips
D) Phillips
Strap wrench is best for? A) Breaking free frozen pipe B) Fitting into narrow gaps C) turning metal or plastic pipe D) working in tight places
C) Turning metal or plastic pipe
If you let the back of the hook jaw touches the pipe, the gripping action will be? A) increased B) reduced C) most effective D) impossible
B) Reduced
When tracking a pipe, you should make _____ complete turn(s) around it. A) One B) Two C) Three D) Four
A) One
What tool is used to cut threads on inside of pipe fitting? A) reamer B) tap C) track D) tubing cutter
B) Tap
One of the most important rules of tool maintenance is to? A) Have tools organized B) Keep tools oil free C) Not waste time on minor repairs D) Replace any worn parts
D) Replace any worn parts
A typical plumbing system supplies water at a pressure of ___ to ___ psi? A) 15; 25 B) 25; 60 C) 60; 75 D) 75; 100
B) 25; 60
PVC pipes are used to drain wasted vent piping because they do not corrode and are easy to? A) clean and polish B) cut and join C) paint and mark D) solder and weld
B) Cut and Join
You should plug the over-flow opening in the sink before you use a(n)? A) auger B) drain and trap tape C) Force-cup plunger D) trap spoon
C) Forced-cup plunger
A trap spoon is used for? A) cleaning a trap B) guiding an auger C) pulling a sewer tape D) unclogging a drain
B) Guiding an auger
When installing pipe in a very narrow space such as between a sink and a wall you should use a(n) _______ wrench. A) Basin B) End-Hex C) Internal D) Pipe
A) Basin
What source should you primarily follow for specifications on electrical work? A) Electrician’s Union B) Facting Mutual C) National Electric Code D) Under Writers Laboratories
C) National Electric Code
What do you use for pulling electrical wires through conduit is called? A) basket cable grips B) fish tape C) raceway D) wire puller
B) Fish tape
Diagonal pliers have? A) cutters on one side B) cutting jaws at an angle to the handles C) long slender jaws and blunt points D) slip-joint jaws
B) Cutting jaws at an angle to the handles
If you need to start a screw in a hard to reach area, use a(n) ________ screwdriver. A) electrician’s B) offset C) ratchet-handle D) split-tip
D) Split-tip
You use a neon circuit tester for? A) measuring voltage B) shutting off the flow of electricity C) testing for grounded electrical outlets D) testing for split-core amperage
C) Testing for grounded electrical outlets
A ripsaw usually has _____ points per inch? A) 2 to 4 B) 4 to 8 C) 10 to 12 D) 12 to 14
B) 4 to 8
A block plane is best for? A) cutting a straight, smooth surface B) cutting the end grain of wood C) general work D) rough work and preliminary smoothing
B) Cutting the end grain of wood
Which part of an auger bit chips the wood from the bottom of the hole? A) Feed Screw B) Lips C) Nibs D) Spurs
B) Lips
A Forster bit is especially useful for drilling a hole? A) all the way through a piece of wood B) in a piece of metal C) with a diameter smaller than 1/4 inch D) with a flat bottom
D) With a flat bottom
Plumb is the ______ of a surface. A) Horizontal paring B) Horizontal trueness C) Vertical paring D) Vertical trueness
D) Vertical trueness
Portland cement needs _____ to harden. A) cold B) heat C) moisture D) rapid drying
C) Moisture
A mixture of lime, Portland cement, sand and water is called? A) aggregate B) mortar C) plaster D) spackle
B) Mortar
Hollowing the mortar bed when laying brick slightly? A) allows the brick to breath B) produces a firm bond with the brick C) results in more attractive joint D) uses less mortar
B) produces a firm bond with the brick
A bull Float is a _________ tools? A) Edging B) jointing C) smoothing D) tuck point
C) Smoothing
Glazing tools are used for cutting and installing? A) ceramic tiles B) concrete blocks C) glass window panes D) porcelain fixtures
C) Glass window Panes
The gauge number tells you the _____ of sheet metal? A) composition B) quality C) size D) thickness
D) Thickness
Three types of punches you can use to cut holes in sheet metal are the _____, _____ and _____? A) Center, Hollow, Lever B) Center, Hollow, Solid C) Center, Lever, Solid D) Hollow, Lever, Solid
D) Hollow, Lever, Solid
The color of the grips on a pair of aviation snips indicate the? A) hand (left or right) it will fit B) shape it will cut C) size of the blade D) thickness it will cut
B) Shape it will cut
Which bevel stake shown below is a bevel-edge square stake? A) B) C) D) E)
B) The ‘S’ shaped stake
In soldering the allow that joins two pieces of metal has a melting point _______ the metal? A) higher than B) equal to or higher than C) equal to or lower than D) lower than
D) Lower than
A vise is a tool used for? A) filling B) holding C) notching D) reaming
B) Holding
The “cut” of a file is the ______ of the teeth and their ________? A) angle; depth B) number; angle C) shape; set D) spanning; shape
C) Shape; set
When filing in which direction should you press downward and? A) backward B) forward C) sideways D) does not matter
B) forward
The thread diameter of a tap should be measured with a? A) Rule B) Screw thread gauge C) Screw thread micrometer D) Venier caliper
C) Screw thread micrometer
What thread class do most bolts, screws and studs of regular quality and all around use fall into? A) Class 1 B) Class 2 C) Class 3 D) Class 4
B) Class 2
Manila rope is made from long fibers of? A) Cane B) Hemp C) Nylon D) Polyester
B) Hemp
How can you prevent the end of a fiber rope from unraveling? A) coat it with plastic B) soak it in vegetable oil C) tie a knot in it D) whip it with a cord
D) Whip it with a cord
You cannot tie a knot in a rope made of? A) manila B) nylon C) polypropylene D) wire
D) Wire
Stainless steel ropes are well suited to Marine and industrial applications because they are strong and? A) available in long lengths B) easy to knot C) inexpensive D) resistant to corrosion
D) Resistant to corrosion
Pullers that apply an impact rather than a steady force are called ______ pullers. A) chain load B) jaw C) machine part D) slide hammer
D) Slide Hammer
