test 1

Question 1

At what location must the metallic components of an optical fiber entrance cable be bonded to ground?

Answer 1

In the building, as close as possible to the point of entry

Question 2

What is required to operate powder actuated equipment?

Answer 2

Proof of instruction on how to operate the equipment

Question 3

According to the Ontario Building Code, which CSA rated communication cable(s) may be installed in a computer room floor?

Answer 3

Only FT1, FT4, or FT6

Question 4

What is the minimum diameter sheave (pulley) required for a 1200 pair cable, 3.25 inches in diameter if the bend radius for a multi-pair cable is 10 x OD?

Answer 4

65 inches

Question 5

Which cable type may be substituted for FT4

Answer 5

CMR
CMP
FT6

Question 6

What is the maximum allowable number of Category 5e cables that may be placed in a 1 inch EMT if the cables diameter is 0.226 inches?

Answer 6

8 cable

Question 7

What is the area in square millimetres of a 35 trade size EMT?

Answer 7

940 mm ²

Question 8

Under what dangerous condition does a worker need to wear a fall arrest system?

Answer 8

Falling more than 3 meters onto a concrete floor

Question 9

What is the minimum amount of clearance required between the live parts of a primary protectors and electrical equipment?

Answer 9

90 cm

Question 10

How should the base of a unsecured portable ladder be positioned?

Answer 10

Not less than 1/4 and not more than 1/3 the length of the ladder

Question 11

What is the length of exposed non-rated communication cable used at the service entry to a building is permitted by the Ontario Building Code?

Answer 11

3 m (9 ft 10 in)

Question 12

Which statement is correct regarding how primary protectors are used?

Answer 12

Primary protectors shall be connected between each line conductor and ground

Question 13

An EF is located 20 meters from the exterior edge of a building. To be compliant with the Ontario Building Code, how must the non-FT rated outdoor cable be installed into the EF?

Answer 13

In 17 meters of rigid conduit

Question 14

What is the maximum number of 0.18 inch diameter cables that may be installed in a 2 inch ID pathway?

Answer 14

49 cables

Question 15

What section in the CEC would you find the rules for Conductors for a Class 2 power and Data Circuits?

Answer 15

Section 16

Question 16

What is the allowable ampacity for a 24 awg, 75 ºC, 8 conductor Class 2 power and Data circuit, when using only 4 conductors and bundled with 1 other cable?

Answer 16

1.96 A

Question 17

What is the minimum number of clips required to support a straight run of 21 trade size EMT, 80 feet long without any junction boxes?

Answer 17

16 clips

Question 18

What type of hard hat is recommended for Construction work?

Answer 18

Class E, Type 2

Question 19

What is the minimum number of clips required to support a straight run of 1 inch EMT, 75 feet long connected 2 pull boxes

Answer 19

12 clips

Question 20

What is the area in square inches of a 27 mm EMT?

Answer 20

0.8335in²

Question 21

What is the maximum AWG of the protector grounding conductor that is protecting 6 fuses circuits?

Answer 21

12 AWG

Question 22

What is the minimum clearance requirement between communication conductors and lightning conductors?

Answer 22

2 M

Question 23

What is the ampacity of a 22 awg, 90 ºC, 8-conductor Communication cable, using all 8 conductors, and bundled with 7 other cables?

Answer 23

1.4 A

Question 24

What Table in the CEC refers to the Allowable Ampacity for Copper, Eight Conductor, Class 2 power and data Communication Circuit cables (PoE)?

Answer 24

Table 60

Question 25

According to the CEC, which cable type has the equivalent rating of FT6?

Answer 25

CMP

Question 26

What is the minimum distance requires between the top of a cable tray and the ceiling where there is no obstruction?

Answer 26

300 mm

Question 27

What is the smallest allowable trade size conduit required to install two. 0.5 inch diameter cables?

Answer 27

35 Trade size Conduit