Structure: Control Structures Flashcards
When used in conjunction with a comparison operator, tests whether a certain condition has been reached, such as an input being above a certain number.
if (conditional) and ==, !=, <, > (comparison operators)
if (someVariable \> 50)
{
// do something here
}
The program tests to see if someVariable is greater than 50. If it is, the program takes a particular action. Put another way, if the statement in parentheses is true, the statements inside the brackets are run. If not, the program skips over the code.
The brackets may be omitted after an if statement. If this is done, the next line (defined by the semicolon) becomes the only conditional statement.
if (x > 120) digitalWrite(LEDpin, HIGH);
if (x > 120)
digitalWrite(LEDpin, HIGH);
if (x > 120){ digitalWrite(LEDpin, HIGH); }
if (x > 120){
digitalWrite(LEDpin1, HIGH);
digitalWrite(LEDpin2, HIGH);
} // all are correct
The statements being evaluated inside the parentheses require the use of one or more operators:
Comparison Operators
x == y (x is equal to y)
x != y (x is not equal to y)
x < y (x is less than y)
x > y (x is greater than y)
x <= y (x is less than or equal to y)
x >= y (x is greater than or equal to y)
Warning
Beware of accidentally using the single equal sign (e.g. if (x = 10) ). The single equal sign is the assignment operator, and sets x to 10 (puts the value 10 into the variable x). Instead use the double equal sign (e.g. if (x == 10) ), which is the comparison operator, and tests whether x is equal to 10 or not. The latter statement is only true if x equals 10, but the former statement will always be true.
This is because C evaluates the statement if (x=10) as follows: 10 is assigned to x (remember that the single equal sign is the assignment operator), so x now contains 10. Then the ‘if’ conditional evaluates 10, which always evaluates to TRUE, since any non-zero number evaluates to TRUE. Consequently, if (x = 10) will always evaluate to TRUE, which is not the desired result when using an ‘if’ statement. Additionally, the variable x will be set to 10, which is also not a desired action.
Allows greater control over the flow of code than the basic if statement, by allowing multiple tests to be grouped together. For example, an analog input could be tested and one action taken if the input was less than 500, and another action taken if the input was 500 or greater.
if/else
if (pinFiveInput \< 500)
{
// action A
}
else
{
// action B
}
- else can proceed another if test, so that multiple, mutually exclusive tests can be run at the same time.*
Each test will proceed to the next one until a true test is encountered. When a true test is found, its associated block of code is run, and the program then skips to the line following the entire if/else construction. If no test proves to be true, the default else block is executed, if one is present, and sets the default behavior.
Note that an else if block may be used with or without a terminating else block and vice versa. An unlimited number of such else if branches is allowed.
if (pinFiveInput \< 500)
{
// do Thing A
}
else if (pinFiveInput \>= 1000)
{
// do Thing B
}
else
{
// do Thing C
}
You can also do branching with switch cases statements.
It is used to repeat a block of statements enclosed in curly braces. An increment counter is usually used to increment and terminate the loop. This statement is useful for any repetitive operation, and is often used in combination with arrays to operate on collections of data/pins.
for
There are 3 parts of a for loop
for (initialization; condition; increment)
{
//statement(s);
}
The initialization happens first and exactly once. Each time through the loop, the condition is tested; if it’s true, the statement block, and the increment is executed, then the condition is tested again. When the condition becomes false, the loop ends.
Example
// Dim an LED using a PWM pin int PWMpin = 10; // LED in series with 470 ohm resistor on pin 10
void setup()
{
// no setup needed
}
void loop()
{
for (int i=0; i \<= 255; i++){
analogWrite(PWMpin, i);
delay(10);
}
}
The C for loop is much more flexible than for loops found in some other computer languages, including BASIC. Any or all of the three header elements may be omitted, although the semicolons are required. Also the statements for initialization, condition, and increment can be any valid C statements with unrelated variables, and use any C datatypes including floats. These types of unusual for statements may provide solutions to some rare programming problems.
For example, using a multiplication in the increment line will generate a logarithmic progression:
for(int x = 2; x < 100; x = x * 1.5){
println(x);
}
Generates: 2,3,4,6,9,13,19,28,42,63,94
controls the flow of programs by allowing programmers to specify different code that should be executed in various conditions. In particular, this statement compares the value of a variable to the values specified in the statements. When this statement is found whose value matches that of the variable, the code in that instance is run.
The break keyword exits the statement, and is typically used at the end of each case. Without a break statement, the ______ statement will continue executing the following expressions (“falling-through”) until a break, or the end of the statement is reached.
switch statemetn
Example
switch (var)
{
case 1:
//do something when var equals 1
break;
case 2:
//do something when var equals 2
break;
default:
// if nothing else matches, do the default
// default is optional
}
Syntax
switch (var)
{
case label:
// statements
break;
case label:
// statements
break;
default:
// statements
}
will loop continuously, and infinitely, until the expression inside the parenthesis, () becomes false. Something must change the tested variable, or the loop will never exit. This could be in your code, such as an incremented variable, or an external condition, such as testing a sensor.
while
Syntax
while(expression)
{
// statement(s)
}
Example
var = 0;
while(var < 200)
{
// do something repetitive 200 times
var++;
}
works in the same manner as the while loop, with the exception that the condition is tested at the end of the loop, so the loop will always run at least once.
do-while
Syntax
do
{
// statement block
} while (test condition);
Example
do
{
delay(50); // wait for sensors to stabilize
x = readSensors(); // check the sensors
} while (x < 100);
is used to exit from a do, for, or while loop, bypassing the normal loop condition. It is also used to exit from a switch statement.
break
for (x = 0; x < 255; x ++)
{
analogWrite(PWMpin, x);
sens = analogRead(sensorPin);
if (sens > threshold){ // bail out on sensor detect
x = 0;
break;
}
delay(50);
}
skips the rest of the current iteration of a loop (do, for, or while). It continues by checking the conditional expression of the loop, and proceeding with any subsequent iterations.
continue
Example
for (x = 0; x < 255; x ++)
{
if (x > 40 && x < 120){ // create jump in values
continue;
}
analogWrite(PWMpin, x);
delay(50);
}
Terminate a function and return a value from a function to the calling function, if desired.
return
Syntax
return;
return value; // both forms are valid
- Parameters*
value: any variable or constant type - Example*
A function to compare a sensor input to a threshold
int checkSensor()
{
if (analogRead(0) \> 400) {
return 1;
else{
return 0;
}
}
Transfers program flow to a labeled point in the program
goto
Syntax
label:
goto label; // sends program flow to the label
Tip
The use of goto is discouraged in C programming, and some authors of C programming books claim that the goto statement is never necessary, but used judiciously, it can simplify certain programs. The reason that many programmers frown upon the use of goto is that with the unrestrained use of goto statements, it is easy to create a program with undefined program flow, which can never be debugged.
With that said, there are instances where a goto statement can come in handy, and simplify coding. One of these situations is to break out of deeply nested for loops, or if logic blocks, on a certain condition.
Example
for(byte r = 0; r \< 255; r++)
{
for(byte g = 255; g \> -1; g--){
for(byte b = 0; b \< 255; b++){
if (analogRead(0) \> 250){ goto bailout;}
// more statements ...
}
}
}
bailout:
