Landing Gear Flashcards
Wheel brake temperatures are displayed: [8.140.10]
A. As a status message.
B. On the hydraulic synoptic.
C. On the gear synoptic.
D. On the EICAS below the gear indicator.
C. On the gear synoptic.
During takeoff, RTO autobraking will not occur unless groundspeed is above:
[8.140.10]
A. 85 knots.
B. 75 knots.
C. 80 knots.
D. 100 knots.
D. 100 knots.
During landing, auto brake application begins: [8.140.10]
A. When both thrust levers are retarded to idle.
B. When spoilers deploy.
C. With wheel spinup.
D. A and C.
D. A and C.
Select the TRUE statement about alternate gear extension. [8.140.10]
A. The landing gear free falls to the down and locked position.
B. Nose landing gear extends when land gear lever is positioned down.
C. Landing gear cannot be retracted after alternate extension.
D. The landing gear lever must be in the down position.
A. The landing gear free falls to the down and locked position.
How do you know that the parking brake is set? [8.140.10]
A. Normal and alternate brake pressures are available.
B. The EICAS memo message PARKING BRAKE SET is displayed.
C. The parking brake lever is in the up position.
D. The brake pressure gage is in the green band.
B. The EICAS memo message PARKING BRAKE SET is displayed.
Which autobrake mode provides the highest deceleration rate for landing? [8.140.10]
A. AUTOBRAKE 3.
B. AUTOBRAKE 4.
C. RTO.
D. MAX AUTOBRAKE.
D. MAX AUTOBRAKE.
Which of the following is true regarding gear down and locked sequence: [8.140.10]
A. Hydraulic pressure unlocks the uplocks, gear falls by gravity, hydraulic
pressure closes the gear doors.
B. Mechanical linkage unlocks the uplocks, gear falls with hydraulic assist, gear
doors close via mechanical linkage.
C. Electric motor unlocks the uplocks, gear falls by gravity, hydraulic pressure
closes the gear doors.
D. Hydraulic pressure unlocks doors, unlocks the uplocks, lowers the gear, and
closes the gear doors.
A. Hydraulic pressure unlocks the uplocks, gear falls by gravity, hydraulic
pressure closes the gear doors.
The landing gear speed limits for all configurations and modes are . [8.140.20]
A. 280 / .80
B. 270 / .82
C. 290 / .84
D. 285 / .85
B. 270 / .82
Hydraulic power for gear retraction and extension is supplied by the: [8.140.10]
A. Reserve hydraulic system.
B. Right hydraulic system.
C. Left hydraulic system.
D. Center hydraulic system.
D. Center hydraulic system.
If an RTO is initiated below 85 knots groundspeed, the RTO autobrake function:
[8.140.10]
A. Does not operate.
B. Operates in the minimum function.
C. Operates in the MAX AUTO rate.
D. Operates in the maximum function.
A. Does not operate.
Which of the following will disarm the autobrake system and cause the EICAS
“AUTOBRAKE” advisory message to display? [8.140.10]
A. Selection of the Autobrake switch to Disarm.
B. Loss of IRSs.
C. RTO is initiated above 85 knots, but autobraking has not been applied.
D. All of the above.
D. All of the above.
The autobrake system disarms if: [8.140.10]
A. Pedal braking is applied.
B. Either thrust lever is advanced.
C. An antiskid system failure occurs.
D. All of the above.
D. All of the above.
What does the alternate landing gear extension system use to extend the gear?
[8.140.10]
A. A dedicated DC hydraulic pump and center hydraulic system fluid.
B. A reserve hydraulic booster to open the doors.
C. A pneumatically powered pump to open the gear doors.
D. C1 hydraulic pump pressure.
A. A dedicated DC hydraulic pump and center hydraulic system fluid.
What is provided by the RTO function of the autobrake system? [8.140.10]
A. The RTO function automatically applies the maximum programmable
deceleration rate when the thrust levers are retarded to idle above 65 knots.
B. The RTO function automatically applies maximum brake pressure when a
thrust reverser lever is moved to idle reverse.
C. The RTO function automatically applies maximum brake pressure when the
thrust levers are retarded to idle above 85 knots groundspeed.
D. The RTO function automatically applies maximum brake pressure when the
thrust levers are retarded to idle above 85 knots indicated airspeed.
C. The RTO function automatically applies maximum brake pressure when the
thrust levers are retarded to idle above 85 knots groundspeed.
If center hydraulic system fluid quantity is low, is it likely that the gear actuation
system has lost all available pressure sources? [8.140.10]
A. No, if center hydraulic system fluid quantity is low, the center system fluid is
isolated to provide an alternate extension source.
B. Yes, if center hydraulic system fluid quantity is low, the alt. extension system
has lost all available pressure sources.
C. No, if center hydraulic system fluid quantity is low, the C1 demand pump is
isolated from the center hydraulic system to provide gear extension and nose
wheel steering source.
D. Yes, if center hydraulic system fluid quantity is low, the alternate gear actuation
levers must be used.
A. No, if center hydraulic system fluid quantity is low, the center system fluid is
isolated to provide an alternate extension source.
