How the braking system works Flashcards
What are they operated by?
What are the 2 types of brakes?
Modern cars have brakes on all four wheels, operated by a hydraulic system. The brakes may be disc type or drum type. friction helps the car slow down or stop.
Which brakes play a greater role in stopping the car?
The front brakes play a greater part in stopping the car than the rear ones, because braking throws the car weight forward on to the front wheels.
Which are more effective? Disc or Drum? And where are they strategically located?
When are all disc used or all drum used for all wheels?
Many cars therefore have disc brakes, which are generally more efficient, at the front and drum brakes at the rear.
All-disc braking systems are used on some expensive or high-performance cars, and all-drum systems on some older or smaller cars.
Brake hydraulics
What are the two types of cylinders and what are they filled with?
Which cylinder has greater surface pushing area?
A hydraulic brake circuit has fluid-filled master and slave cylinders connected by pipes.
When you push the brake pedal it depresses a piston in the master cylinder, forcing fluid along the pipe.
The fluid travels to slave cylinders at each wheel and fills them, forcing pistons out to apply the brakes.
Fluid pressure distributes itself evenly around the system.
The combined surface ‘pushing’ area of all the slave pistons is much greater than that of the piston in the master cylinder.
Consequently, the master piston has to travel several inches to move the slave pistons the fraction of an inch it takes to apply the brakes.
SERVO-ASSISTED BRAKING
A direct-acting servo is fitted between the brake pedal and the master cylinder. The pedal can work the master cylinder directly if the servo fails or if the engine is not running.
This arrangement allows great force to be exerted by the brakes, in the same way that a long-handled lever can easily lift a heavy object a short distance.
Most modern cars are fitted with twin hydraulic circuits, with two master cylinders in tandem, in case one should fail.
Sometimes one circuit works the front brakes and one the rear brakes; or each circuit works both front brakes and one of the rear brakes; or one circuit works all four brakes and the other the front ones only.
Under heavy braking, so much weight may come off the rear wheels that they lock, possibly causing a dangerous skid.
For this reason, the rear brakes are deliberately made less powerful than the front.
Most cars now also have a load-sensitive pressure-limiting valve. It closes when heavy braking raises hydraulic pressure to a level that might cause the rear brakes to lock, and prevents any further movement of fluid to them.
Advanced cars may even have complex anti-lock systems that sense in various ways how the car is decelerating and whether any wheels are locking.
Such systems apply and release the brakes in rapid succession to stop them locking.
How do disc brakes work?
A disc brake has a disc that turns with the wheel. The disc is straddled by a caliper, in which there are small hydraulic pistons worked by pressure from the master cylinder.
The pistons press on friction pads that clamp against the disc from each side to slow or stop it. The pads are shaped to cover a broad sector of the disc.
There may be more than a single pair of pistons, especially in dual-circuit brakes.
The pistons move only a tiny distance to apply the brakes, and the pads barely clear the disc when the brakes are released. They have no return springs.
Rubber sealing rings round the pistons are designed to let the pistons slip forward gradually as the pads wear down, so that the tiny gap remains constant and the brakes do not need adjustment.
Many later cars have wear sensors leads embedded in the pads. When the pads are nearly worn out, the leads are exposed and short-circuited by the metal disc, illuminating a warning light on the instrument panel.
How do drum brakes work?
A drum brake has a hollow drum that turns with the wheel. Its open back is covered by a stationary backplate on which there are two curved shoes carrying friction linings.
The shoes are forced outwards by hydraulic pressure moving pistons in the brake’s wheel cylinders, so pressing the linings against the inside of the drum to slow or stop it.
Each brake shoe has a pivot at one end and a piston at the other. A leading shoe has the piston at the leading edge relative to the direction in which the drum turns.
DRUM BRAKE
A drum brake with a leading and trailing shoe, which has only one hydraulic cylinder; brakes with two leading shoes have a cylinder for each shoe and are fitted to the front wheels on an all-drum system.
The rotation of the drum tends to pull the leading shoe firmly against it when it makes contact, improving the braking effect.
Some drums have twin leading shoes, each with its own hydraulic cylinder; others have one leading and one trailing shoe - with the pivot at the front.
This design allows the two shoes to be forced apart from each other by a single cylinder with a piston in each end.
It is simpler but less powerful than the two-leading-shoe system, and is usually restricted to rear brakes.
In either type, return springs pull the shoes back a short way when the brakes are released.
Shoe travel is kept as short as possible by an adjuster. Older systems have manual adjusters that need to be turned from time to time as the friction linings wear. Later brakes have automatic adjustment by means of a ratchet.
Drum brakes may fade if they are applied repeatedly within a short time - they heat up and lose their efficiency until they cool down again. Discs, with their more open construction, are much less prone to fading.
The handbrakes
The handbrake
Apart from the hydraulic braking system, all cars have a mechanical handbrake acting on two wheels - usually the rear ones.
The handbrake gives limited braking if the hydraulic system fails completely, but its main purpose is as a parking brake.
The handbrake lever pulls a cable or pair of cables linked to the brakes by a set of smaller levers, pulleys and guides whose details vary greatly from car to car.
A ratchet on the handbrake lever keeps the brake on once it is applied. A push button disengages the ratchet and frees the lever.
On drum brakes, the handbrake system presses the brake linings against the drums.
Disc brakes sometimes have a comparable handbrake arrangement, but because it is difficult to place the linkage on a compact caliper, there may be a completely separate set of handbrake pads for each disc.
