Exam Practice Flashcards

0
Q

Why do you open the vent valve before starting the vacuum?

A

To prevent motor overload.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
1
Q

How many millimeters equals one pound of pressure?

A

52 millimeters.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

The onan generator should be started loaded?.?

A

False

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

The metric standard of temperature C degrees used a range of…

A

0-100 degrees.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

If there are 2.54 centimeters in an inch, and 36 inches in a yard, the # of centimeters in a yard is…..

A

91.44 centimeters.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

The symbol / means….

A

Normal joint with short circuited sleeve insulation standard bonding.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

The feeder # and voltage can be found in the ______ on a feeder map.

A

Title box.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

A typical decrease in temperature in the reservoir will cause ____

A

A corresponding decrease in pressure in the reservoir.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

A normal temperature increase in the cable sheath will cause ____

A

The level in the reservoir to raise.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

The type of hammer that has the head entirely fabricated with soft shock absorbing material is the _______.

A

Mallet.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

The most popular angle at offset for the jaws of an open end wrench is ?

A

15 degrees.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Gas pliers are also known as?

A

Eagle claws.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

The Phillips screwdriver is available in how many sizes?

A

4

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

The materials which can be used for soft faced hammers include?

A

Lead, brass, and rawhide.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

A ___ in a smooth jaw adjustable wrench used on large union nut.

A

Ford wrench.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

The type of chisel used to cut narrow surfaces is ?

A

Cape.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

When the tubing sticks too far out of the flaring tool when it is flared, the type of damage that will occur is called?

A

Necking.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

To change the size of the tubing a tubing bender can bend you must change the ______

A

Roller adapters.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

The typical pressure range of a reservoir is____

A

2-30 psi.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

In a CC type reservoir, the tank is filled with____

A

Idle oil.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

____ is the typical volume capacity of a reservoir.

A

10-20 gallons

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

A DC type reservoir _______

A

Has cells filled with degasified oil.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

A DC type reservoir is _____

A

Fed directly into pothead.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

In an AC/BICC reservoir type reservoir, the gas in the cell is usually adjusted to ____when the tank is full.

24
In an AC/BICC reservoir type reservoir, the cell is full of____
Gas.
25
AC reservoirs are ____ because the full pressure range cannot be utilized.
Relatively inefficient
26
Before removing a CC reservoir disconnect ____
The fluid level switch.
27
When a reservoir adjustment is found is found to be at or above the high check point.
Measure temps to determine if the reservoir is in adjustment by the curve.
28
An oil level is read by using a sight glass (which reservoir)
CC type
29
If a thermometer is used on a CC type reservoir when placed in the well,
It must contact the lead sheath.
30
When cable section is not supervised by an alarm, readings should be taken at least
Three times a week(72hours)
31
If a section has a minor leak requiring close monitoring, readings on a non supervised section shall be taken
Three days
32
For DC type reservoirs when two reservoirs are connected in parrallel
The pressure in only one needs to be measured
33
Fluid pressure setting tolerance for DC type reservoir is
.5 min and .5 below max
34
To find out how many gallons of fluid are in an AC reservoir
The insulating pressure must be measured
35
Who should physically check the positions of valves during a valve verification check
Splicer and helper
36
When the ______ seals the valves it is witnessed by the ______
Helper and splicer
37
Fluid leaks in dielectric systems are critical because,
They reduce the insulating abilities of the system
38
A likely location for a CO2 leak in a DC reservoir is
Auxiliary gas tank connections
39
If a loose fitting is the suspected cause of a fluid leak
Tighten the suspected fitting
40
You are working on feeder 69M43-44 in the MH. The CMX-270 doesn't work what should you do?
Stop the job
41
It is not necessary to treat the oil on BICC truck
False
42
When performing a code 51, who verifies the valve positions?
Second man
43
When adjusting reservoir,the Barton relay valve should be closed
True
44
Closed circuit means
Light on; section clear
45
A steady light on the supervisory board indicates an alarm
True
46
The oil in the plant or BICC truck must be tested for gas contents before it can be used
True
47
When working in a manhole, how often do you check the atmosphere?
Every two hours
48
The oil temperature in the plant should not exceed
85 degrees f
49
Who's responsible for safety?
Everyone (all of the above)
50
DC or CC type reservoirs are identical?
True
51
If a Barton relay is at zero mm what is the percentage of oil in the reservoir?
50%
52
After completing a joint treatment, which hose do you disconnect first?
Bottom hose
53
What is a code 47?
Relay calibration
54
What type of reservoir is used in a feeding section?
CC,DC, BICC (all of the above)
55
In a BICC reservoir the oil is located in the cell
False
56
It is not necessary to make a flush connection when servicing cable reels.
False
57
To have a good vacuum, the barometer reading on the manometer should total approximately 762mm
True